Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2416-15 Touch Sensor Circuit Rh Open

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2416-15 Touch Sensor Circuit Rh Open

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2416-15

Touch sensor circuit RH open

(Touch sensor circuit right hand open) 		Diagnosis condition All times
Signal (terminal) Touch sensor RH signal
Threshold

Automatic back door control unit detects when one of the following conditions is satisfied

  • Touch sensor RH circuit is open or shorted

  • Malfunction of touch sensor RH
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (touch sensor RH circuit is open or shorted)

  • Automatic back door control unit

  • Touch sensor RH

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK TOUCH SENSOR INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+) (–) Condition

Voltage

(Approx.)
Automatic back door control unit
Connector Terminal
B55 13 Ground Touch sensor RH Detect obstruction 0.2 – 3 V
Other than above 3.4 – 6.5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 5.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK TOUCH SENSOR CIRCUIT

  1. Disconnect automatic back door control unit connector and touch sensor RH connector.

  2. Check continuity between automatic back door control unit harness connector and touch sensor RH harness connector.

    Automatic back door control unit Touch sensor RH Continuity
    Connector Terminal Connector Terminal
    B55 13 D515 1 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 13 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK TOUCH SENSOR GROUND CIRCUIT

  1. Disconnect touch sensor LH connector.

  2. Check continuity between automatic back door control unit harness connector and touch sensor RH harness connector.

    Automatic back door control unit Touch sensor RH Continuity
    Connector Terminal Connector Terminal
    B55 14 D515 4 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 14 Ground No

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace harness.

CHECK TOUCH SENSOR

Check touch sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace touch sensor RH. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. B2409-14 Half Latch Switch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2409-14 Half latch switch (Half latch switch) Diagnosis con...
    Dtc/circuit Diagnosis. B2419-12 Open Switch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2419-12 Open switch (Open switch) Diagnosis condition When ...

    Other materials:

    Dtc/circuit Diagnosis. Door Switch
    Component Function Check CHECK FUNCTION CONSULT Select “Door switch driver”, “Door switch assist”, “Door switch rear left” and “Door switch rear right” in “Data monitor” mode of "BCM [DOOR LOCK]". Check that the function operates normally according to the followin ...

    Dtc/circuit Diagnosis. Power Window Motor
    Front (passenger Side) Component Function Check CHECK FUNCTION Check front power window motor (passenger side) operation with power window main switch (passenger side switch) or front power window switch (passenger side). Is the inspection result normal? YES>> Inspection End. NO> ...

    Symptom Diagnosis. Take Away Warning Does Not Operate
    Diagnosis Procedure CHECK COMBINATION METER BUZZER Check combination meter buzzer. Refer to Diagnosis Procedure (Full TFT meter) or Diagnosis Procedure (7 inch information display). Is the inspection result normal? YES>> GO TO 2. NO>> Repair or replace the malfunctioning parts. ...