Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Power Window Main Switch

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Mirrors / Dtc/circuit Diagnosis :: Power Window Main Switch

Diagnosis Procedure (Without automatic drive positioner system)

CHECK POWER WINDOW MAIN SWITCH CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect power window main switch connector and door mirror connector.

  3. Check continuity between power window main switch harness connector and door mirror harness connector.

    Power window main switch Door mirror Continuity
    Connector Terminal Connector Terminal
    D27 6 Door mirror LH D14 11 Yes
    21 5
    10 4
    8 Door mirror RH D107 11
    7 5
    9 4

  4. Check continuity between power window main switch harness connector and ground.

    Power window main switch — Continuity
    Connector Terminal
    D27 6 Ground No
    21
    10
    8
    7
    9

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

REPLACE DOOR MIRROR

Replace door mirror . Refer to Removal and Installation.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 3.

REPLACE POWER WINDOW MAIN SWITCH

Replace power window main switch. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 4.

REPLACE BCM

Replace BCM. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

>>

Inspection End.

Diagnosis Procedure (With automatic drive positioner system)

CHECK POWER WINDOW MAIN SWITCH CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect power window main switch connector and door mirror LH connector.

  3. Check continuity between power window main switch harness connector and door mirror LH harness connector.

    Power window main switch Door mirror LH Continuity
    Connector Terminal Connector Terminal
    D6 2 D16 6 Yes
    6 10
    7 5
    8 13
    10 3
    14 14
    21 2

  4. Check continuity between power window main switch harness connector and ground.

    Power window main switch — Continuity
    Connector Terminal
    D6 2 Ground No
    6
    7
    8
    10
    14
    21

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

REPLACE DOOR MIRROR LH

Replace door mirror LH. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 3.

REPLACE POWER WINDOW MAIN SWITCH

Replace power window main switch. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 4.

REPLACE BCM

Replace BCM. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

>>

Inspection End.

    Dtc/circuit Diagnosis. B2ccf-04 Passenger Door Mirror Control Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2CCF-04 Passenger door mirror control module (Passenger doo...
    Dtc/circuit Diagnosis. Passenger Door Mirror Control Module
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuse is not blown (open): Unit Location Fuse No. Capacity Passenger door mirror control module Fuse ...

    Other materials:

    Fuel Level Sensor Signal Circuit
    Component Function Check PERFORM COMPONENT FUNCTION CHECK (1) Ignition switch OFF. Disconnect fuel level sensor unit, fuel pump and FPCM (fuel level sensor) (main) harness connector. Connect variable resistor between harness connector terminals located on the Nissan Ariya vehicle s ...

    Removal and Installation. Intelligent Key Warning Buzzer
    Removal and Installation REMOVALFOR USA AND JAPAN EARLY PRODUCTION AND USA LATE PRODUCTIONRemove front bumper fascia. Refer to Removal and Installation. Disconnect Intelligent Key warning buzzer harness connector. Disengage clip of frame, and then remove Intelligent Key warning buzzer (1). ...

    Dtc/circuit Diagnosis. C18e4-88 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18E4 88 CAN communication system 1 Diagnosis condition When Ignition switch is ON. Signal (terminal) CAN communication signal Threshold When Electrically-driven Intelligent ...