Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B14e5-64 Adas Control Unit System

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: B14e5-64 Adas Control Unit System

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
B14E5 64 Brake control system Diagnosis condition When Ignition switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from ADAS control unit 2.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E5-64" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to INTERMITTENT INCIDENT.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK ADAS CONTROL UNIT 2 SYSTEM

Perform self-diagnosis for “ICC/ADAS 2”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES>>

GO TO 3.

NO>>

Inspection End.

CHECK 12V BATTERY

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES>>

GO TO 5.

NO>>

Inspection End.

CHECK CONNECTOR TERMINALS

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Connect Electrically-driven Intelligent Brake Unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Ignition switch OFF to ON without depressing the brake pedal.

  4. Ignition switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  6. Ignition switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Ignition switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  10. Ignition switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES>>

GO TO 7.

NO>>

Inspection End.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector.

  5. Check the Electrically-driven Intelligent Brake Unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES ("B14E5-64")>>

Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "B14E5-64")>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. B14e3-02 Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition B14E3 02 Wheel sensor Diagnosis condition Ignition switch is ON. Signal (terminal) Rear ...
    Dtc/circuit Diagnosis. C18d0-01 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18D0 01 Backup power supply unit Diagnosis condition When Ignition switch is ON. Signal...

    Other materials:

    With Idle Start/stop. Symptom Diagnosis. Charging System
    Charging System Symptom Table Symptom Reference Discharged 12V battery Refer to Work Flow (With EXP-800 NI or GR8-1200 NI) or Work Flow (Without EXP-800 NI or GR8-1200 NI). The charge warning lamp does not illuminate when the ignition switch is set to ON. The charge warning lamp ...

    P0606 Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0606 00 CONTROL MODULE (Control module processor) Diagnosis condition — Signal (terminal) — Threshold Malfunction in ECM processor Di ...

    P11a0 Vcr Control Module
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A0 00 VCR control module (Variable compression ratio control module) Diagnosis condition — Signal (terminal) — Threshold Malfunction in ...