Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B14e3-64 Wheel Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: B14e3-64 Wheel Sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
B14E3 64 Wheel sensor 1 Diagnosis condition Ignition switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When difference between the rear right wheel sensor and the wheel speed other than the rear right wheel sensor is 6 km/h (4 MPH) or more [when driving 100 km/h (62 MPH) or less].
Diagnosis delay time 18 seconds or more
2 Diagnosis condition Ignition switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When difference between the rear right wheel sensor and the wheel speed other than the rear right wheel sensor is 6% or more [when driving 100 km/h (62 MPH) or less].
Diagnosis delay time 1 second or less
3 Diagnosis condition Ignition switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rotation speed of rear right wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition Ignition switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When rear right wheel sensor is different rotation direction from wheel sensor other than front wheel left.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Rear right wheel sensor

  • Electrically-driven Intelligent Brake Unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CAUTION:

Never check between wheel sensor harness connector terminals.

CHECK 12V BATTERY

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–64" detected?

YES>>

GO TO 3.

NO>>

Inspection End.

CHECK WHEEL SENSOR

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

CONSULT

  1. Replace the rear right wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Ignition switch OFF to ON without depressing the brake pedal.

  4. Ignition switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  6. Ignition switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Ignition switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  10. Ignition switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 5.

NO>>

Inspection End.

CHECK CONNECTOR

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery negative terminal.

  4. Check the Electrically-driven Intelligent Brake Unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect 12V battery negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 7.

NO>>

Inspection End.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector.

  5. Check the Electrically-driven Intelligent Brake Unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 9.

NO>>

Inspection End.

CHECK WHEEL SENSOR HARNESS

  1. Disconnect 12V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity
      Connector Terminal Connector Terminal
      E125 22 B67 1 Existed

    • Measurement connector and terminal for signal circuit

      ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity
      Connector Terminal Connector Terminal
      E125 37 B67 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

CONSULT

  1. Connect Electrically-driven Intelligent Brake Unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Ignition switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  7. Ignition switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Ignition switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  11. Ignition switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 11.

NO>>

Inspection End.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect Electrically-driven Intelligent Brake Unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: NI-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester Ignition switch ON.

    NOTE:

    The green POWER indicator should illuminate. If the POWER indicator does not illuminate, replace the battery in the ABS active wheel sensor tester before proceeding.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

    NOTE:

    If the red SENSOR indicator illuminates but does not flash, reverse the polarity of the tester leads and retest.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to Removal and Installation.

  2. Connect Electrically-driven Intelligent Brake Unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Ignition switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  7. Ignition switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Ignition switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  11. Ignition switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. B14e3-4a Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition B14E3 4A Wheel sensor Diagnosis condition Ignition switch is ON. Signal (terminal) Rear ...
    Dtc/circuit Diagnosis. B14e4-64 Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition B14E4 64 Wheel sensor 1 Diagnosis condition Ignition switch is ON. Signal (terminal) Whe...

    Other materials:

    Heated steering wheel
    Example Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light A will illuminate once the system is active. If the steering wheel surface temperature is below 86–104ºF (30–40ºC), the system will automatically heat the wheel and cycle o ...

    System maintenance
    To ensure proper operation of the driver monitoring system on the Nissan Rogue, keep the camera and surrounding area clean. Use a soft, damp cloth—such as one designed for lens cleaning—wrung out thoroughly, and gently wipe the surface to remove dust or dirt. License information (ProPILOT Ass ...

    P1c90-49 Sub Starter & Generator
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1C90-49 Sub starter & generator (Sub starter & generator) Diagnosis condition Engine running at idle Signal (terminal) - Threshold Sub starte ...