Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B14e0-4a Wheel Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: B14e0-4a Wheel Sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
B14E0 4A Wheel sensor Diagnosis condition Ignition switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When front left wheel sensor is installed to wrong position.
Diagnosis delay time 3 seconds or less

POSSIBLE CAUSE

  • Front left wheel sensor

  • Electrically-driven intelligent brake unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–4A" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CAUTION:

Never check between wheel sensor harness connector terminals.

CHECK 12V BATTERY

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E0–4A" detected?

YES>>

GO TO 3.

NO>>

Inspection End.

REPLACE WHEEL SENSOR

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is the display result "B14E0-4A" of “CRNT”?

YES>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. B14e0-09 Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition B14E0 09 Wheel sensor Diagnosis condition Ignition switch is ON. Signal (terminal) Front...
    Dtc/circuit Diagnosis. B14e3-02 Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition B14E3 02 Wheel sensor Diagnosis condition Ignition switch is ON. Signal (terminal) Rear ...

    Other materials:

    Dtc/circuit Diagnosis. Passenger Door Mirror Control Module
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuse is not blown (open): Unit Location Fuse No. Capacity Passenger door mirror control module Fuse block (J/B) 45 5 A   Is the fuse blown (open) ? YES>> Replace the bl ...

    Ventilation, Heater & Air Conditioner. Ventilation System
    Precaution :: Precautions Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to t ...

    Basic Inspection. Shipping Mode Cancel Operation
    Work Procedure SHIPPING MODE CANCEL OPERATION Ignition switch OFF. Push in (switch on) the extended storage fuse switch. Refer to How To Check. Ignition switch ON. Ignition switch OFF and wait at least 2 seconds. >> GO TO 2. SHIPPING MODE CANCEL CHECK Igniti ...