Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B0002-1e Driver Airbag Module 2

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag Control System / Dtc/circuit Diagnosis :: B0002-1e Driver Airbag Module 2

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B0002-1E

DRIVER AIRBAG MODULE 2

(Driver Frontal Stage 2 Deployment Control) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module signal
Threshold

Driver air bag module 2 circuit is shorted to driver air bag module 1.

(including the spiral cable)
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAGNOSIS RESULT

CONSULT

  1. Ignition switch ON.

  2. Perform “Self diagnosis result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

CHECK SPIRAL CABLE CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect driver air bag module connector and spiral cable connector.

  3. Check continuity between spiral cable terminals.

    Terminal Continuity
    39 37 Not existed
    38
    40 37

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace spiral cable. Refer to Removal and Installation.

REPLACE DRIVER AIR BAG MODULE

  1. Replace driver air bag module. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 5.

NO>>

Inspection End

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End

    Dtc/circuit Diagnosis. B0002-1b Driver Airbag Module 2
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0002-1B DRIVER AIRBAG MODULE 2 (Driver Frontal Stage 2 Depl...
    Dtc/circuit Diagnosis. B0002-55 Driver Airbag Module 2
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0002-55 DRIVER AIRBAG MODULE 2 (Driver Frontal Stage 2 Depl...

    Other materials:

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    Dtc/circuit Diagnosis. Horn Function
    Component Function Check CHECK FUNCTION CONSULT Ignition switch OFF. Perform “Horn” in “Active test” mode of “IPDM E/R”. Check the horn operation. Test item Description Horn On Horn Sounds (for 20 ms.) Is the operation normal? YES>> Ins ...

    Power Supply and Ground Circuit
    8ch Can Gateway Diagnosis Procedure CHECK FUSE Check that the following fuse are not blown. Signal name Fuse No. Battery power supply 16 Ignition power supply 9 Is the fuse blown (open)? YES>> Replace the blown fuse after repairing the affected circuit if a fuse ...