Nissan Rogue (T33) 2021-Present Service Manual: Diagnosis System (around View Monitor Control Unit)

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Audio, Visual & Navigation System / Intelligent Around View Monitor :: System Description / Diagnosis System (around View Monitor Control Unit)

Consult Function

CONSULT FUNCTIONS

CONSULT performs the following functions via the communication with the around view monitor control unit.

Diagnosis mode Function
Self diagnosis result The around view monitor control unit self diagnosis results are displayed.
ECU identification The around view monitor control unit part number is displayed.
Work supports Changes setting of each function.
Data monitor The around view monitor control unit input/output data is displayed in real time.
Replace ECU Writes the Nissan Ariya vehicle specification when replacing the around view monitor control unit.

SELF DIAGNOSIS RESULT

Refer to DTC Index.

Freeze Frame Data (FFD)

The following vehicle status is recorded when DTC is detected and is displayed on CONSULT.

Item name [Unit] Display content

ODO/TRIP METER

[km] 		Total driving distance (odometer value) upon DTC detection is displayed.

Number of occurrences of fault

[count] 		Displays the number of times DTC was detected

Nissan Ariya VehicleSpeed1

[km/h] 		Displays the vehicle speed when DTC is detected.
Power supply state Displays the power supply status when DTC is detected.
GADE Displays the DTC detection function status
Shift position Displays the shift position when DTC is detected.

ECU IDENTIFICATION

The part number of around view monitor control unit is displayed.

WORK SUPPORTS

Work support items Description
MAC key writing Writes MAC key to around view monitor control unit.
PREDICTIVE COURSE LINE DISPLAY Select on/off for predictive course line.
MOD function

Select ON/OFF for MOD function.

NOTE:

After selection, turn OFF the ignition switch.
Initialize camera image calibration

The calibration can be initialized to factory shipment condition.

NOTE:

Calibration of camera image caused by misalignment of the camera installation position is performed.
Fine tuning of Birds-Eye view Performs the Birds-Eye view fine tuning.
Parameter writing (All camera) When replacing each camera, it is necessary to write the camera parameters using CONSULT.
Calibrating camera image Performs the camera calibration.
OTA status reset

NOTE:

This item display, but not use.

DATA MONITOR

NOTE:

The table below also includes information (items) that are not applicable to this Nissan Ariya vehicle. Check the display contents of CONSULT for this vehicle adaptation information (item).

Display Item Remarks

Power supply state

[State1/State2/State3/ State4/State5/State6/State7/ State8/State9/State10/ State11/State12] 		Displays the value of around view monitor control unit power supply.

GADE

[Sleep or crank malfunction disable/Auto ACC malfunction disable/All malfunction disable/All malfunction enable/Firmware update Over The Air software malfunction/Unavailable] 		Displays the DTC detection function status

Shift position

[Parking/Neutral/Rear/Drive/Unavailable] 		Displays the shift position

REVERSE SIGNAL

[On/Off] 		Reception status of shift position (reverse) signal received from TCM is displayed.

CAMERA SWITCH SIGNAL

[On/Off] 		Reception status of camera switch signal received from AV control unit is displayed.

CAMERA OFF SIGNAL

[On/Off] 		Reception status of camera OFF signal received from AV control unit is displayed.

REAR CAMERA IMAGE SIGNAL

[OK/NG] 		Input status of rear camera image signal is displayed in real time.

Rear camera communication status

[OK/NG] 		Communication status of rear camera is displayed in real time.

Rear camera communication line

[OK/NG] 		Status of communication line of rear camera is displayed in real time.

Front camera image signal

[OK/NG] 		Input status of front camera image signal is displayed in real time.

Front camera communication status

[OK/NG] 		Communication status of front camera is displayed in real time.

Front camera communication line

[OK/NG] 		Status of communication line of front camera is displayed in real time.

Left camera image signal

[OK/NG] 		Input status of side camera LH image signal is displayed in real time.

Left camera communication status

[OK/NG] 		Communication status of side camera LH is displayed in real time.

Left camera line

[OK/NG] 		Status of communication line of side camera LH is displayed in real time.

Right camera image signal

[OK/NG] 		Input status of side camera RH image signal is displayed in real time.

Right camera communication status

[OK/NG] 		Communication status of side camera RH is displayed in real time.

Right camera line

[OK/NG] 		Status of communication line of side camera RH is displayed in real time.

Folding motor voltage 1

[Low/N/High/RESERVE] 		Input status of retractable power door mirror operation signal input to around view monitor control unit is displayed in real time.

Folding motor voltage 2

[Low/N/High/RESERVE] 		Input status of retractable power door mirror operation signal input to around view monitor control unit is displayed in real time.

Image output

[None/Yes] 		Displays the image signal transmission status in real time.

Average Nissan Ariya vehicle speed

[mph/km/h] 		Displays the vehicle speed calculated from the wheel speed.

Nissan Ariya VehicleSpeed1

[mph/km/h] 		Displays the value of vehicle speed signal.

REPLACE ECU

Writes the vehicle specification when replacing around view monitor control unit.

    System
    Intelligent Around View Monitor With 8" Color Display System Description SYSTEM DIAGRAMAround View Monitor Control Unit Input Signal (CAN Communication) Transmit unit Signal nam...
    Intelligent Around View Monitor. Ecu Diagnosis Information. Around View Monitor Control Unit
    Around View Monitor Control Unit With 8" Color Display Reference Value VALUES ON THE DIAGNOSIS TOOLNOTE: The following table includes information (items) inapplicable to this Ni...

    Other materials:

    Dtc/circuit Diagnosis. U0075-00 Communication Bus C Off
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U0075-00 Control module comm Bus C Off (Control module communication Bus C Off) Diagnosis condition Ignition switch ON Signal (terminal) CAN communication s ...

    Lane Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the terminals and connectors of the front camera unitfor damage, bend and loose connection (unit side and connector side). Is the inspection result no ...

    Heated steering wheel
    Example Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light A will illuminate once the system is active. If the steering wheel surface temperature is below 86–104ºF (30–40ºC), the system will automatically heat the wheel and cycle o ...