Nissan Rogue (T33) 2021-Present Service Manual: Cooling Fan

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / Cooling Fan

Component Function Check

CHECK COOLING FAN FUNCTION

With CONSULT

  1. Turn ignition switch ON.

  2. Perform “FAN DUTY CONTROL” in “ACTIVE TEST” mode of “ECM” using CONSULT.

  3. Touch “LOW”, “HI” on the CONSULT screen.

  4. Check that cooling fan operates.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK COOLING FAN CONTROL MODULE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect cooling fan control module harness connector.

  3. Check the voltage between cooling fan control module harness connector and ground.

    + − Voltage
    Cooling fan control module-1
    Connector Terminal
    F109 2 Ground Battery voltage
    + − Voltage
    Cooling fan control module-2
    Connector Terminal
    F110 2 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error ‐ detected parts.

CHECK COOLING FAN CONTROL MODULE GROUND CIRCUIT

  1. Check the continuity between cooling fan control module harness connector and ground.

    + − Continuity
    Cooling fan control module-1
    Connector Terminal
    F109 1 Ground Existed
    + − Continuity
    Cooling fan control module-2
    Connector Terminal
    F110 1 Ground Existed

  2. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK COOLING FAN CONTROL SIGNAL CIRCUIT

  1. Disconnect IPDM E/R harness connector.

  2. Check the continuity between cooling fan control module harness connector and IPDM E/R harness connector.

    Cooling fan control module-1 IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F109 4 E63 106 Existed
    Cooling fan control module-2 IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F110 4 E63 106 Existed

  3. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

    Charge Air Cooler Electric Water Pump Relay
    Component Inspection CHECK ELECTRIC WATER PUMP RELAY Turn ignition switch OFF. Remove electric water pump relay. Check the continuity between electric water pump relay terminals...
    Crankcase Pressure Sensor
    Diagnosis Procedure CHECK CRANKCASE PRESSURE SENSOR POWER SUPPLY Turn ignition switch OFF. Disconnect crankcase pressure sensor connector. Turn ignition switch ON. Check the vol...

    Other materials:

    Removal and Installation. Mood Lamp (center Console)
    Exploded View Mood lamp (center console) assembly (Bulb type) Center console assembly Mood lamp (center console tray) assembly (LED type) : Pawl : Nissan Ariya Vehicle front Removal & Installation REMOVALCAUTION: Disconnect the battery negative terminal or rem ...

    Dtc/circuit Diagnosis. U1327-52 Mac Key Update
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U1327-52 MAC key update (Message authentication code key update) Diagnosis condition - Signal (terminal) - Threshold MAC key writing is incomplete. ...

    P0850 Pnp Switch
    DTC Description DESCRIPTIONTransmission range switch is turn ON when the selector lever is P or N.ECM detects the position because the continuity of the line (the ON) exists.DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0850 00 ...