Nissan Rogue (T33) 2021-Present Service Manual: Component Parts /circuit Diagnosis :: B2494-19 Heated Steering Wheel Relay

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering System / Component Parts /circuit Diagnosis :: B2494-19 Heated Steering Wheel Relay

DTC description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
B2494-19 Heated steering wheel relay Diagnosis condition Power switch ON
Signal (Terminal) Heated steering wheel relay control circuit
Threshold Heated steering wheel relay control circuit is open or shorted to ground
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Fuse

  • Heated steering wheel relay

  • A/C auto amp.

  • Harness or connectors (heated steering wheel relay control circuit is open or shorted to ground)

FAIL-SAFE

Heated steering wheel operation is stopped

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “HVAC”.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open).

Unit Location Fuse No. Capacity
Heated steering wheel relay Fuse block (J/B) #62 10A
Heated steering wheel relay Fuse block (J/B) #40 10A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK HEATED STEERING WHEEL RELAY CONTROL SIGNAL CIRCUIT

  1. Disconnect A/C auto amp. connector.

  2. Ignition switch ON.

  3. Check voltage between A/C auto amp. harness connector and ground.

    + - Voltage
    A/C auto amp.
    Connector Terminal
    M55 56 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

GO TO 3.

CHECK HEATED STEERING WHEEL RELAY POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Remove heated steering wheel relay.

  3. Ignition switch ON.

  4. Check voltage between heated steering wheel relay harness connector and ground.

    + - Voltage
    Heated steering wheel relay
    Connector Terminal
    M95 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair harness or connector.

CHECK HEATED STEERING WHEEL RELAY CONTROL SIGNAL CIRCUIT FOR SHORT

  1. Ignition switch OFF.

  2. Check continuity between heated steering wheel relay harness connector and ground.

Steering heater relay — Continuity
Connector Terminal
M95 2 Ground No

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK HEATED STEERING WHEEL RELAY

Check heated steering wheel relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace heated steering wheel relay.

Component Inspection

CHECK HEATED STEERING WHEEL RELAY

  1. Ignition switch OFF.

  2. Remove heated steering wheel relay.

  3. Check continuity between heated wheel relay terminals.

    Terminal Condition Continuity
    Heated steering wheel relay
    3 5 12 V direct current supply between terminals 1 and 2. Yes
    No current supply No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace heated steering wheel relay.

    Component Parts /circuit Diagnosis. B2494-13 Heated Steering Wheel Relay
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition B2494-13 Heated steering wheel relay Diagnosis condition Power switch ON Signal (Termina...
    Component Parts /circuit Diagnosis. Heated Steering Wheel System
    Component Function Check CHECK HEATED STEERING WHEEL SYSTEM Check the heated steering wheel system. Refer to System Description (Heated Steering Wheel). Is the inspection result...

    Other materials:

    Dtc/circuit Diagnosis. B0010-11 Assist A/b Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0010-11 ASSIST A/B MODULE (Passenger Frontal Stage 1 Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Passenger air ba ...

    2wd. Preparation. Preparation
    Preparation Special Service Tool Tool number (TechMate No.) Tool name Description KV40104000 ( – ) Hub lock nut wrench a: 85 mm (3.35 in) b: 65 mm (2.56 in) Removing and Installing wheel hub lock nut. KV40107300 ( – ) Boot band crimping tool Installing bo ...

    C10b1-01 Parking Brake Actuator (lh)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B1 01 Parking brake actuator (LH) [Parking brake actuator (left)] Diagnosis condition When parking brake is apply or release Signal (terminal) — ...