Nissan Rogue (T33) 2021-Present Service Manual: Component Parts /circuit Diagnosis :: B2494-13 Heated Steering Wheel Relay

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering System / Component Parts /circuit Diagnosis :: B2494-13 Heated Steering Wheel Relay

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
B2494-13 Heated steering wheel relay Diagnosis condition Power switch ON
Signal (Terminal) Heated steering wheel relay control circuit
Threshold Heated steering wheel relay control circuit is open or shorted to ground
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Fuse

  • Heated steering relay

  • A/C auto amp.

  • Harness or connectors (heated steering wheel relay control circuit is open or shorted to ground)

FAIL-SAFE

Heated steering wheel operation is stopped

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Power switch ON.

  2. Select “Self diagnosis result” mode of “HVAC”.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open).

Unit Location Fuse No. Capacity
Heated steering wheel relay Fuse block (J/B) #62 10A
Heated steering wheel relay Fuse block (J/B) #40 10A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK HEATED STEERING WHEEL RELAY CONTROL SIGNAL CIRCUIT

  1. Disconnect A/C auto amp. connector.

  2. Ignition switch ON.

  3. Check voltage between A/C auto amp. harness connector and ground.

    + - Voltage
    A/C auto amp.
    Connector Terminal
    M55 56 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

GO TO 3.

CHECK HEATED STEERING WHEEL RELAY POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Remove steering heater relay.

  3. Ignition switch ON.

  4. Check voltage between steering heater relay harness connector and ground.

    + - Voltage
    Steering heater relay
    Connector Terminal
    M95 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair harness or connector.

CHECK STEERING HEATER RELAY CONTROL SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Check continuity between steering heater relay harness connector and A/C auto amp. harness connector.

Steering heater relay A/C auto amp. Continuity
Connector Terminal Connector Terminal
M95 2 M55 56 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK HEATED STEERING RELAY RELAY CONTROL SIGNAL CIRCUIT FOR SHORT

Check continuity between steering heater relay harness connector and ground.

Steering heater relay — Continuity
Connector Terminal
M95 2 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair harness or connector.

CHECK HEATED STEERING WHEEL RELAY

Check heated steering wheel relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace heated steering wheel relay.

Component Inspection

CHECK HEATED STEERING WHEEL RELAY

  1. Ignition switch OFF.

  2. Remove heated steering wheel relay.

  3. Check continuity between heated wheel relay terminals.

    Terminal Condition Continuity
    Heated steering wheel relay
    3 5 12 V direct current supply between terminals 1 and 2. Yes
    No current supply No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace heated steering wheel relay.

    Ecu Diagnosis Information. A/c Auto Amp.
    List of ECU Reference ECUReference A/C auto amp. Reference Value Fail-safe DTC Index
    Component Parts /circuit Diagnosis. B2494-19 Heated Steering Wheel Relay
    DTC description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition B2494-19 Heated steering wheel relay Diagnosis condition Power switch ON Signal (Termina...

    Other materials:

    C0513 Wheel Speed Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C0513 00 Right rear wheel speed sensor (Right Rear Wheel Speed Sensor Range/Performance) Diagnosis condition Ignition switch ON Battery voltage: 11 V ...

    Dtc/circuit Diagnosis. U2141-87 Can Comm Circuit
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...