Nissan Rogue (T33) 2021-Present Service Manual: Component Parts /circuit Diagnosis :: Heated Steering Wheel System
Component Function Check
CHECK HEATED STEERING WHEEL SYSTEM
Check the heated steering wheel system. Refer to System Description (Heated Steering Wheel).
Is the inspection result normal?
YES>>Inspection End.
NO>>Go toDiagnosis Procedure.
Diagnosis Procedure
CHECK POWER SOURCE AND GROUND CIRCUIT
-
Ignition switch OFF.
-
Remove the heated steering wheel. Refer to Removal and Installation.
-
Ignition switch ON.
CAUTION:
Never start the engine.
-
Turn heated steering wheel switch ON.
-
Check voltage between spiral cable harness connector terminals.
Spiral cable Condition Voltage (Approx.) Connector Terminals M163 43 44 Within 30 seconds after turning ON the heated steering switch. Battery voltage Other conditions. 0 V
Is the inspection result normal?
YES>>GO TO 2.
NO>>GO TO 3.
CHECK HEATED STEERING WHEEL
Check heated steering wheel. Refer to Component Inspection (Heated Steering Wheel).
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace heated steering wheel. Refer to Removal and Installation.
CHECK GROUND CIRCUIT
Check continuity between spiral cable harness connector terminal and ground.
| Spiral cable | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M163 | 43 | Ground | Yes |
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace damaged parts.
CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND SPIRAL CABLE
-
Ignition switch OFF.
-
Disconnect heated steering wheel relay connector. Refer to Component Parts Location.
-
Disconnect spiral cable connector.
-
Check continuity between heated steering wheel relay harness connector terminal and spiral cable harness connector terminal.
Heated steering wheel relay Spiral cable Continuity Connector Terminal Connector Terminal M95 5 M163 44 Yes -
Check continuity between heated steering wheel relay harness connector terminal and ground.
Heated steering wheel relay — Continuity Connector Terminal M95 5 Ground No
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace damaged parts.
CHECK HEATED STEERING WHEEL RELAY
Check heated steering wheel relay. Refer to Component Inspection (Heated Steering Wheel Relay).
Is the inspection result normal?
YES>>GO TO 6.
NO>>Replace heated steering wheel relay. Refer to Component Parts Location.
DETECT MALFUNCTIONING ITEM
Check the following.
-
Battery
-
Harness for short or open between battery and fuse block (J/B).
-
10A fuse [No. 62 and 40, located in the fuse block (J/B)]. Refer to Wiring Diagram.
-
Fuse block (J/B)
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace damaged parts.
CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND A/C AMP.
-
Check continuity between heated steering wheel relay harness connector terminal and A/C amp. harness connector terminal.
Heated steering wheel relay A/C amp. Continuity Connector Terminal Connector Terminal M95 2 M55 56 Yes -
Check continuity between heated steering wheel relay harness connector terminal and ground.
Heated steering wheel relay — Continuity Connector Terminal M95 2 Ground No
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace damaged parts.
CHECK HARNESS BETWEEN A/C amp. AND HEATED STEERING WHEEL SWITCH
-
Check continuity between A/C amp. harness connector terminal and heated A/C switch assembly harness connector terminal.
A/C amp. A/C switch assembly Continuity Connector Terminal Connector Terminal M55 68 M84 7 Yes -
Check continuity between heated steering wheel relay harness connector terminal and ground.
Heated steering wheel relay — Continuity Connector Terminal M95 2 Ground No
Is the inspection result normal?
YES>>GO TO 9.
NO>>Repair or replace damaged parts.
CHECK HEATED STEERING WHEEL SWITCH
Check heated steering wheel switch. Refer to Component Inspection (Heated Steering Wheel Switch).
Is the inspection result normal?
YES>>Repair or replace A/C amp. Refer to Removal and Installation.
NO>>Replace A/C switch assembly. Refer to Removal and Installation.
Component Inspection (Heated Steering Wheel Switch)
PERFORM SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result� mode of “HVAC�.
-
Check DTC.
Is B24B4-02 detected?
YES>>GO TO 2.
NO>>Inspection End.
PERFORM SELF DIAGNOSTIC RESULT
CONSULT
-
Select “ERASE�.
-
Ignition switch OFF.
-
Ignition switch ON.
-
Perform “DTC CONFIRMATION PROCEDURE�. Refer to DTC Description.
Is DTC detected again?
YES>>Replace A/C switch assembly. Refer to Removal and Installation.
NO>>Inspection End.
Component Inspection (Heated Steering Wheel)
CHECK HEATED STEERING WHEEL CONTINUITY
Check continuity between spiral cable connector terminals.
| Spiral cable | Condition | Continuity | |
|---|---|---|---|
| Terminals | |||
| 43 | 44 | Leather surface temperature of 68°F (20°C) or less | Yes |
| Leather surface temperature of 86°F (30°C) or more | No | ||
Is the inspection result normal?
YES>>GO TO 2.
NO>>Replace heated steering wheel. Refer to Removal and Installation.
CHECK HEATED STEERING WHEEL RESISTANCE
Check resistance between spiral cable connector terminals.
| Spiral cable | Condition | Resistance (Ω) (Approx.) | |
|---|---|---|---|
| Terminals | |||
| 43 | 44 | Leather surface temperature of 68°F (20°C) or less | 1.8 – 2.2 |
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace heated steering wheel. Refer to Removal and Installation.
Component Inspection (Heated Steering Wheel Relay)
CHECK HEATED STEERING WHEEL RELAY CONTINUITY
Check continuity between heated steering wheel relay terminals.
CAUTION:
Connect the fuse between the terminals when applying the voltage.
| Heated steering wheel relay | Condition | Continuity | |
|---|---|---|---|
| Terminal | |||
| 3 | 5 | Apply 12 V direct current between terminals 1 and 2. | Yes |
| Other conditions. | No | ||
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace heated steering wheel relay. Refer to Component Parts Location.
Other materials:
Vehicle Security System
System Description
SYSTEM DIAGRAM Component Function
Door switch
Door switch detects door open/close condition and then transmits door switch signal to BCM.
IPDM E/R
IPDM E/R operates horns with horn request signal received from BCM.
IPDM E/R operates headlamps with high be ...
P2097 A/f Sensor 1
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P2097
00
POST CATALYST FUEL TRIM SYS B1
(Post catalyst fuel trim system too rich bank 1)
Diagnosis condition
—
Signal (terminal)
Air fuel ratio (A/F) ...
Adjustment of Brake Caliper Initial Position
Description
CAUTION:
When performing the following operations, always use
CONSULT (It cannot be performed by any means other than CONSULT.), for
performing "INITIALIZATION POSITION ADJUSTMENT" of "WORK SUPPORT". Refer
to Work Procedure.
×: Required —: not required Procedure INITIALIZATI ...
