Nissan Rogue (T33) 2021-Present Service Manual: C1f89-83 Side Radar Lh
Without Propilot Assist 2.1
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| C1F89 | 83 |
Side radar rear LH (Side radar rear left hand) |
Diagnosis condition | When engine is running |
| Signal (terminal) | CAN communication signal | |||
| Threshold | ADAS control unit 2 detects an error signal that is received from side radar LH via CAN communication | |||
| Diagnosis delay time | 1 second or less | |||
POSSIBLE CAUSE
Side radar LH
FAIL-SAFE
The following systems are canceled.
-
BSW
-
I-BSI
-
RCTA
CONFIRMATION PROCEDURE
CHECK DTC PRIORITY
If DTC “C1F89-83” is displayed with Network-DTC, first diagnose the Network-DTC.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Index.
NO>>GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine.
-
Perform “All DTC Reading” with CONSULT.
-
Check if the “C1F89-83” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.
Is “C1F89-83” detected as the current malfunction?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
With Propilot Assist 2.1
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| C1F89 | 83 |
Side radar rear LH (Side radar rear left hand) |
Diagnosis condition | When engine is running |
| Signal (terminal) | CAN communication signal | |||
| Threshold | ADAS control unit 2 detects an error signal that is received from side radar rear LH via CAN communication | |||
| Diagnosis delay time | 1 second or less | |||
POSSIBLE CAUSE
-
Side radar rear LH
-
ADAS control unit 2
FAIL-SAFE
The following systems are canceled.
-
Lane keep function*
-
Lane change support function
-
Overtaking support function
-
Route driving support function
-
Blind Spot Intervention
*: ProPILOT Assist 2.1 display is blue
CONFIRMATION PROCEDURE
CHECK DTC PRIORITY
If DTC “C1F89-83” is displayed with Network-DTC, first diagnose the Network-DTC.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Index.
NO>>GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine.
-
Perform “All DTC Reading” with CONSULT.
-
Check if the “C1F89-83” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.
Is “C1F89-83” detected as the current malfunction?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK DTC PRIORITY
If DTC “C1F89-83” is displayed with Network-DTC, first diagnose the Network-DTC.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Index.
NO>>GO TO 2.
CHECK SIDE RADAR LH SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “Side radar (Rear left)”.
Is any DTC detected?
YES>>Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.
NO>>Replace the ADAS control unit 2. Refer to Removal and Installation.
Other materials:
Steering Switch Signal B Circuit
Component Function Check
CHECK COMBINATION METER INPUT SIGNAL
CONSULT
Ignition switch ON.
Select “Steering switch input” in “Data monitor” mode of “M&A”.
Check that the function operates normally according to the following conditions:
Condition Value
CONTRO ...
C0513 Wheel Speed Sensor
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
C0513
00
Right rear wheel speed sensor
(Right Rear Wheel Speed Sensor Range/Performance)
Diagnosis condition
Ignition switch ON
Battery voltage: 11 V ...
Dtc/circuit Diagnosis. C1731-16 Tire Pressure Sensor Fl
DTC Description
NOTE:
The Signal Tech II Tool [– (NI-50190)] can be used to
perform the following functions: Refer to the Signal Tech II User Guide
for additional information.
Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTCs ...