Nissan Rogue (T33) 2021-Present Service Manual: C1f80-12 Steering Wheel Touch Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / C1f80-12 Steering Wheel Touch Sensor

Without Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1F80 12

Steering wheel touch sensor

(Steering wheel touch sensor) 		Diagnosis condition When engine is running
Signal (terminal) Steering wheel touch sensor status signal (LIN communication signal)
Threshold Receiving voltage error of steering wheel touch sensor
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Steering wheel touch sensor power supply or ground circuit

  • Steering wheel touch sensor

  • ADAS control unit 2

FAIL-SAFE

The following system are cancelled.

  • Vehicle-to-vehicle distance control mode

  • Steering wheel assistance function

  • Conventional (fixed speed) cruise control mode

  • FEB

  • RAB

  • PFCW

  • LDP

  • Blind Spot Intervention

  • TSR

  • DAA

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine, and then wait for 2 seconds or more.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F80-12” is detected as the current malfunction in self-diagnosis results of “ICC/ADAS 2”.

Is “C1F80-12” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

With Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1F80 12

Steering wheel touch sensor

(Steering wheel touch sensor) 		Diagnosis condition When engine is running
Signal (terminal) Steering wheel touch sensor status signal (LIN communication signal)
Threshold Receiving voltage error of steering wheel touch sensor
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Steering wheel touch sensor power supply or ground circuit

  • Steering wheel touch sensor

  • ADAS control unit 2

FAIL-SAFE

None

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine, and then wait for 2 seconds or more.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F80-12” is detected as the current malfunction in self-diagnosis results of “ICC/ADAS 2”.

Is “C1F80-12” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REPLACE STEERING WHEEL

  1. Replace steering wheel. Refer to Removal and Installation.

  2. Perform confirmation procedure again. Refer to DTC Description (Without ProPILOT Assist 2.1) or DTC Description (With ProPILOT Assist 2.1).

Is “C1F80-12” detected as the current malfunction?

YES>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

NO>>

INSPECTION END

    C1f80-11 Steering Wheel Touch Sensor
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1F80 11 Steering wheel touch sensor...
    C1f80-49 Steering Wheel Touch Sensor
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1F80 49 Steering wheel touch sensor...

    Other materials:

    Dtc/circuit Diagnosis. B0010-11 Assist A/b Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0010-11 ASSIST A/B MODULE (Passenger Frontal Stage 1 Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Passenger air ba ...

    System maintenance
    To ensure proper operation of the driver monitoring system on the Nissan Rogue, keep the camera and surrounding area clean. Use a soft, damp cloth—such as one designed for lens cleaning—wrung out thoroughly, and gently wipe the surface to remove dust or dirt. License information (ProPILOT Ass ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...