Nissan Rogue (T33) 2021-Present Service Manual: C1f71-87 Ethernet Circuit
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| C1F71 | 87 |
Ethernet circuit (Ethernet circuit) |
Diagnosis condition | When engine is running |
| Signal (terminal) | Ethernet | |||
| Threshold | If ADAS control unit 2 is not receiving ethernet communication signal from distance sensor | |||
| Diagnosis delay time | 5 seconds or more | |||
POSSIBLE CAUSE
-
Ethernet harness
-
ADAS control unit 2
-
Distance sensor
FAIL-SAFE
The following systems are canceled.
-
Vehicle-to-vehicle distance control mode
-
Conventional (fixed speed) cruise control mode
-
Steering wheel assistance function
-
AEB
-
RAB
-
I-FCW
-
LDW
-
I-LI
-
BSW
-
I-BSI
-
RCTA
-
TSR
-
I-DA
CONFIRMATION PROCEDURE
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine and wait at least 5 seconds.
-
Perform “All DTC Reading” with CONSULT.
-
Check if the DTC “C1F71-87” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.
Is DTC “C1F71-87” detected as the current malfunction?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
-
Ignition switch OFF.
-
Check the ethernet harness connectors and terminals of ADAS control unit 2 and distance sensor for damage or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunction part, securely lock the harness connector.
PERFORM ALL DTC READING
-
Ignition switch ON.
-
Perform “All DTC Reading” with CONSULT.
-
Check if any DTCs of ethernet (DTC “C2599-13” and/or “U275F-88”) are detected in “Self Diagnostic Result” of “LASER/RADAR”
Are any DTCs of ethernet detected?
YES>>Replace the ADAS control unit 2 (Refer to Removal and Installation), and GO TO 3.
NO>>Replace the distance sensor. Refer to Removal and Installation.
PERFORM DTC CONFIRMATION PROCEDURE-1
-
Erases all self-diagnosis results with CONSULT.
-
Perform DTC confirmation procedure again. Refer to DTC Description.
Is DTC “C1F71-87” detected as the current malfunction?
YES>>Replace the distance sensor (Refer to Removal and Installation), and GO TO 4.
NO>>INSPECTION END
PERFORM DTC CONFIRMATION PROCEDURE-2
-
Erases all self-diagnosis results with CONSULT.
-
Perform DTC confirmation procedure again. Refer to DTC Description.
Is DTC “C1F71-87” detected as the current malfunction?
YES>>Replace the ethernet harness between ADAS control unit 2 and distance sensor.
NO>>INSPECTION END
Other materials:
I-BSI driving situations
Basic information
Indicator on
Indicator off
Indicator flashing
Illustration 1 — Approaching from behind
Another vehicle approaching from behind
Illustration 1: When another vehicle enters the monitored area from the rear in an adjacent lane, the side indicator light on the Nissan Rogue i ...
Reporting safety defects
For USA
If you believe that your vehicle has a defect that could cause a crash or lead to injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN. This applies whether you drive a Nissan Rogue or another NISSAN model.
...
B2721-11 Center Sensor [rl]
DTC Description
DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B2721-11
CENTER SENSOR [RL]
(Center sensor [RL])
Diagnosis condition
When ignition switch is ON
Signal (terminal)
Rear sonar sensor signal LH inner
Threshold ...
