Nissan Rogue (T33) 2021-Present Service Manual: C1f05-49 Front Camera Unit
Without Propilot Assist 2.1
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| C1F05 | 49 |
Front camera unit (Front camera unit) |
Diagnosis condition | When engine is running |
| Signal (terminal) | — | |||
| Threshold | If front camera unit is malfunctioning | |||
| Diagnosis delay time | 1 second or less | |||
NOTE:
DTC "C1F05-49" may be detected when CONSULT is communicating with ABS actuator and electric unit (control unit) since the control function of ABS actuator and electric unit (control unit) is temporary stopped.
POSSIBLE CAUSE
Front camera unit
FAIL-SAFE
The following systems are canceled.
-
Vehicle-to-vehicle distance control mode
-
Conventional (fixed speed) cruise control mode
-
Steering wheel assistance function
-
AEB
-
LDW
-
I-LI
-
I-BSI
-
TSR
CONFIRMATION PROCEDURE
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine.
-
Perform “Diagnosis (One System)” of "ICC/ADAS 2" with CONSULT.
NOTE:
When performing "All DTC Reading", DTC “C1F05-49” may be detected because ABS actuator and electric unit (control unit) stops its control function by communicating with CONSULT. Therefore performing "Diagnosis (One System)" is necessary.
-
Check if the “C1F05-49” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.
Is “C1F05-49” detected as the current malfunction?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
With Propilot Assist 2.1
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| C1F05 | 49 |
Front camera unit (Front camera unit) |
Diagnosis condition | When engine is running |
| Signal (terminal) | — | |||
| Threshold | If front camera unit is malfunctioning | |||
| Diagnosis delay time | 1 second or less | |||
POSSIBLE CAUSE
-
Front camera unit
-
ADAS control unit 2
FAIL-SAFE
The following systems are canceled.
-
Lane keep function*1
-
Lane keep function*2
-
Lane change support function
-
Overtaking support function
-
Route driving support function
-
FEB
-
RAB
-
PFCW
-
LDP
-
Blind Spot Intervention
-
TSR
*1: ProPILOT Assist 2.1 display is green
*2: ProPILOT Assist 2.1 display is blue
CONFIRMATION PROCEDURE
CHECK DTC PRIORITY
If DTC “C1F05-49” is displayed with Network-DTC, first diagnose the Network-DTC.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Index.
NO>>GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine.
-
Perform “All DTC Reading” with CONSULT.
-
Check if the “C1F05-49” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.
Is “C1F05-49” detected as the current malfunction?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC confirmation procedure again. Refer to DTC Description.
NOTE:
DTC "C1F05-49" may be detected when CONSULT is communicating with ABS actuator and electric unit (control unit) since the control function of ABS actuator and electric unit (control unit) is temporary stopped.
Is “C1F05-49” detected as the current malfunction?
YES>>Replace the front camera unit. Refer to Removal and Installation.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
Other materials:
System Description. System
System Description (Heated Steering Wheel)
SYSTEM DIAGRAMThe
heated steering wheel switch controls the heated steering wheel relay.
When the heated steering wheel switch is turned on, the heated steering
wheel relay is energized and the heated steering wheel system will
operate. The heated ...
Ecu Diagnosis Information. Bcm
List of ECU Reference
ECU Reference
BCM
Values on the Diagnosis Tool
Reference Value (With Type A Meter)
Reference Value (With Type B Meter)
Fail-safe
DTC Inspection Priority Chart
DTC Index
...
Fuel Pressure Check
Work Procedure
FUEL PRESSURE RELEASEFUEL PRESSURE RELEASE
With CONSULT
Turn ignition switch ON.
Perform “ENGINE” in “WORK SUPPORT” mode with CONSULT.
Start the engine.
After engine stalls, crank it two or three times to release all fuel pressure.
Turn ignition swit ...
