Nissan Rogue (T33) 2021-Present Service Manual: C1212-82 Can Communication (ecm)

Nissan Rogue (T33) 2021-Present Service Manual / Transmission & Driveline :: Driveline / Transfer: Ty92a :: Dtc/circuit Diagnosis / C1212-82 Can Communication (ecm)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detecting condition
C1212-82

CAN COMM (ECM)

[Controller area network communication (engine control module)] 		Diagnosis condition Ignition switch: ON
Signal CAN communication signals
Threshold CAN signal of ECM is unmatched with the previous value. (CAN signal is stuck)
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • ECM

FAIL-SAFE

Although AWD control is canceled, the vehicle can drive at 2WD condition.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h (6 MPH) or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Ariya vehicle.

  4. Perform "Self diagnosis result" mode of “AWD/4WD”.

Is DTC “C1212-82” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSIS OF ECM

CONSULT

Perform "Self diagnosis result" mode of “ECM”.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After placing the ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1212-82” is detected, replace actuator assembly due to the malfunction of the AWD control unit. Refer to Disassembly and Assembly.

NO>>

Repair or replace error-detected parts.

    C1211-82 Can Communication (abs)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1211-82 CAN COMM (ABS) [Controller area network communication (...
    C1213-A2 Control Unit Power Supply
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1213-A2 BATTERY VOLTAGE (Battery voltage) Diagnosis condition I...

    Other materials:

    2wd. Preparation. Preparation
    Preparation Special Service Tool Tool number (TechMate No.) Tool name Description KV40104000 ( – ) Hub lock nut wrench a: 85 mm (3.35 in) b: 65 mm (2.56 in) Removing and Installing wheel hub lock nut. KV40107300 ( – ) Boot band crimping tool Installing bo ...

    Repair Information. Preparation
    Repairing Material Foam Repair During factory body assembly, foam insulators are installed in certain body panels and locations around the Nissan Ariya vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.URETHANE FOAM APPLICATIONSUse commercially availabl ...

    System maintenance
    To ensure proper operation of the driver monitoring system on the Nissan Rogue, keep the camera and surrounding area clean. Use a soft, damp cloth—such as one designed for lens cleaning—wrung out thoroughly, and gently wipe the surface to remove dust or dirt. License information (ProPILOT Ass ...