Nissan Rogue (T33) 2021-Present Service Manual: C10b2-64 Parking Brake Switch

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C10b2-64 Parking Brake Switch

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C10B2 64

Parking brake switch

(Parking brake switch) 		Diagnosis condition When ignition switch is ON
Signal (terminal) Paring brake switch
Threshold When a malfunctioning in the parking brake switch circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • Parking brake switch

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • Parking brake switch

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

  2. Push the parking brake switch.

    CAUTION:

    • Set the electric shift selector in the P position.

    • Depress the brake pedal.

  3. Pull the parking brake switch.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C10B2–64” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK DATA MONITOR

CONSULT

  1. Ignition switch ON.

    CAUTION:

    Be sure wait of 10 seconds after ignition switch ON.

  2. Select “ABS”, “Data Monitor” and “PB SW” according to this order. Check that data monitor displays when parking brake switch is pull, neutral or push. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 2.

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the parking brake switch harness connector for disconnection or looseness.

  3. Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector. GO TO 3.

CHECK PARKING BRAKE SWITCH CIRCUIT

  1. Disconnect the parking brake switch harness connector.

  2. Disconnect the ABS actuator and electric unit (control unit) harness connector.

  3. Check the continuity between ABS actuator and electric unit (control unit) harness connector and parking brake switch harness connector.

    ABS actuator and electric unit (control unit) Parking brake switch Continuity
    Connector Terminal Connector Terminal
    E125 34 M182 9 Existed
    31 7
    16 6
    32 5
    15 3

  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.

    ABS actuator and electric unit (control unit) — Continuity
    Connector Terminal
    E125 34 Ground Not existed
    31
    16
    32
    15

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness or connector. GO TO 4.

CHECK PARKING BRAKE SWITCH

Check the parking brake switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace the parking brake switch. Refer to Removal and Installation.

CHECK TERMINAL

  1. Check parking brake switch terminals for damage or loose connection with harness connector.

  2. Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair/replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect the parking brake switch harness connector.

  2. Connect the ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Ignition switch ON.

  5. Apply and release the parking brake five times.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10B2-64” detected?

YES-1>>

"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End

Component Inspection

CHECK PARKING BRAKE SWITCH

  1. Disconnect 12V battery negative terminal.

  2. Disconnect the parking brake switch harness connector.

  3. Check the continuity when parking brake switch is operated.

    Condition Terminal Continuity
    When parking brake switch is neutral 3 − 5 Existed
    6 − 7 Existed
    3 − 6 Not existed
    5 − 7 Not existed
    When parking brake switch is pull 3 − 5 Existed
    5 − 7 Existed
    3 − 6 Not existed
    6 − 7 Not existed
    When parking brake switch is push 3 − 6 Existed
    6 − 7 Existed
    3 − 5 Not existed
    5 − 7 Not existed

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the parking brake switch. Refer to Removal and Installation.

CHECK PARKING BRAKE SWITCH INDICATOR

Apply 12 V between parking brake switch connector terminals, and check the parking brake switch indicator lamp.

CAUTION:

  • Connect fuse between terminals when applying the voltage.

  • Never make the terminals short.

Parking brake switch Condition Parking brake switch indicator
Terminal
+ —
2 9 Apply 12 V between parking brake switch connector terminals (2 and 9). ON

Is the inspection result normal?

YES>>

Inspection End

NO>>

Replace the parking brake switch. Refer to Removal and Installation.

    C10b2-01 Parking Brake Switch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B2 01 Parking brake switch (Parking brake switch) Diagnos...
    C10b3-44 Parking Brake Control Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B3 44 Parking brake control module (Parking brake control...

    Other materials:

    Difference between predictive and actual distances
    Basic information The displayed guide lines and their positions on the ground are intended only as approximate references. When driving the Nissan Rogue on uphill, downhill, or uneven surfaces, or when objects extend outward, the actual distance may differ from what appears on the monitor relative t ...

    Power Supply and Ground Circuit
    Ecm Diagnosis Procedure CHECK THE BATTERY CABLE Turn ignition switch OFF. Check the battery cable for tightening enough. NOTE: Check the continuity between the battery cable and the battery terminal. Is the inspection result normal? YES>> GO TO 2 ...

    Automatic air conditioner (models without rear control)
    Models with heated steering wheel Models without heated steering wheel Basic information Temperature control dial (driver's side) AUTO button Display screen SYNC button Temperature control dial (passenger's side) ON·OFF button Air recirculation button Fan speed buttons Air flow ...