Nissan Rogue (T33) 2021-Present Service Manual: C10b3-44 Parking Brake Control Module

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C10b3-44 Parking Brake Control Module

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C10B3 44

Parking brake control module

(Parking brake control module) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • Parking brake actuator

  • Rear brake caliper assembly

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • Parking brake actuator

  • Rear brake caliper assembly

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

  2. Push the parking brake switch.

    CAUTION:

    • Set the electric shift selector in the P position.

    • Depress the brake pedal.

  3. Pull the parking brake switch.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C10B3-44” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Ignition switch ON.

  3. Operate parking brake switch (apply/release) five times.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Ignition switch ON.

    CAUTION:

    Be sure wait of 10 seconds after ignition switch ON.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10B3-44” detected?

YES-1>>

"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End

    C10b2-01 Parking Brake Switch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B2 01 Parking brake switch (Parking brake switch) Diagnos...
    C10b3-53 Parking Brake Control Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B3 53 Parking brake control module (Parking brake control...

    Other materials:

    Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
    Work Flow CUSTOMER INTERVIEWInterview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of customer's comments. Refer to Diagnostic Work ...

    Dtc/circuit Diagnosis. U2176-87 Can Comm Err (ccm/st Angle Sensor)
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped ...

    P0011 Ivt Control
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0011 00 INT/V TIM CONT-B1 (“A” Camshaft position - timing over-advanced or system performance bank 1) Diagnosis condition Engine running Signal (term ...