Nissan Rogue (T33) 2021-Present Service Manual: C1071-54 Decel G Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1071-54 Decel G Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1071 54

Decel G sensor

(Decel G sensor) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) -
Threshold When calibration of decel G sensor is not complete.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC
Incomplete calibration of decel G sensor

  • Incomplete calibration of decel G sensor

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Bake assist function

  • Brake force distribution function

  • hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after starting the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1071-54” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CALIBRATION OF DECEL G SENSOR

Perform calibration of decel G sensor. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after starting the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1071-54” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

    C1071-01 Decel G Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1071 64 Decel G sensor (Decel G sensor) Diagnosis condition...
    C1071-61 Decel G Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1071 61 Decel G sensor (Decel G sensor) Diagnosis condition...

    Other materials:

    P0106 Manifold Absolute Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0106 00 ABSL PRES SEN/CIRC (Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance) Diagnosis condition — Signal (terminal) ...

    Symptom Diagnosis. Intelligent Key Low Battery Warning Does Not Operate
    Diagnosis Procedure CHECK INFORMATION DISPLAY Check information display. Refer to Work flow. Is the inspection result normal? YES>> GO TO 2. NO>> Repair or replace the malfunctioning parts. CHECK INTELLIGENT KEY BATTERY Check Intelligent Key battery. Refer to Component Inspe ...

    B2e01-96 Tcu
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E01-96 Internal battery (Internal battery) Diagnosis condition When ignition switch is ON Signal (terminal) Internal battery Threshold Internal ba ...