Nissan Rogue (T33) 2021-Present Service Manual: P0106 Manifold Absolute Pressure Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0106 Manifold Absolute Pressure Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0106 00

ABSL PRES SEN/CIRC

(Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance) 		Diagnosis condition —
Signal (terminal) MAP sensor signal
Threshold

  • Difference between intake manifold pressure and estimated intake manifold pressure while steady driving condition.

  • An excessively low voltage from the sensor is sent to ECM.

  • An excessively high voltage from the sensor is sent to ECM.
Diagnosis delay time 5 consecutive seconds

POSSIBLE CAUSE

  • Harness or connectors

  • MAP sensor

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 1 minute before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Accelerate the Nissan Ariya vehicle from 40 km/h (25MPH) to 70 km/h (44 MPH) or more within 7 seconds.

    CAUTION:

    Always drive Nissan Ariya vehicle in safe manner according to traffic conditions and obey all traffic laws.

    NOTE:

    Keeping the accelerator pedal as steady as possible at approximately 3/8 during the acceleration allows easy diagnosis.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK MAP SENSOR FITTING CONDITION

Check MAP sensor fitting condition.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Adjust parts fitting condition.

CHECK FOR CHARGE AIR LEAK

  1. Start the engine and let it idle.

  2. Listen for an charge air leak.

Is intake air leak detected?

YES>>

Repair or replace error-detected parts.

NO>>

GO TO 3.

CHECK MAP SENSOR HARNESS CONNECTOR CONNECTIONS

Check MAP sensor harness connector connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK MAP SENSOR

Check MAP sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace error-detected parts.

CHECK MAP SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Check the power supply of the MAP sensor.

    + -

    Voltage

    (Approx.)
    MAP sensor
    Connector Terminal
    F86 1 Ground 5.0 V

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Perform trouble diagnosis for power supply circuit.

CHECK MAP SENSOR CIRCUIT FOR OPEN AND SHORT

Check MAP sensor circuit for open and short.

ECM MAP sensor Continuity
Connector Terminal Connector Terminal
F71 80 F86 1 Existed
120 2
106 3

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

    P0103 Maf Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0103 00 MAF SEN/CIRCUIT-B1 (Mass or volume air flow sensor "A" ...
    P0107 Barometric Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0107 00 ABSL PRES SEN/CIRC (Manifold Absolute Pressure/Barometr...

    Other materials:

    Adas Control Unit. Basic Inspection
    Additional Service When Replacing Adas Control Unit 2 Without Propilot Assist 2.1 Work Procedure Always perform the additional service after replacing the ADAS control unit 2.ADAS CONTROL UNIT 2 CONFIGURATION Perform saving Nissan Ariya vehicle internal information according to "Replace ECU" i ...

    P1564 Ascd Steering Switch
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1564 00 ASCD SW (ASCD SW) Diagnosis condition — Signal (terminal) ASCD steering switch signal Threshold ECM detects that input signal from t ...

    Automatic Brake Hold. Basic Inspection. Diagnosis and Repair Work Flow
    Diagnosis and Repair Work Flow Work Flow DETAILED FLOWINTERVIEW FROM THE CUSTOMER Clarify customer complaints before inspection. First of all, perform an interview utilizing Diagnostic Work Sheet and reproduce the symptom as well as fully understand it. Ask customer about his/her complaints ...