Nissan Rogue (T33) 2021-Present Service Manual: P0107 Barometric Pressure Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0107 Barometric Pressure Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0107 00

ABSL PRES SEN/CIRC

(Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low) 		Diagnosis condition Ignition switch ON
Signal (terminal) Manifold absolute pressure (MAP) sensor signal
Threshold An excessively low voltage from the sensor is sent to ECM
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors [Manifold absolute pressure (MAP) sensor circuit is open or shorted.]

  • Manifold absolute pressure (MAP) sensor

FAIL-SAFE

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Ariya vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h (44 MPH) or more is possible.

NOTE:

This value is a reference value converted from engine power to Nissan Ariya vehicle speed. Actual power limitation value differs due to the malfunctioning part and driving condition.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.

  2. Check ground connection. Refer to Ground Inspection in Refer to Circuit Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace ground connection.

CHECK MAP SENSOR

Check MAP sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace MAP sensor. Refer to Removal and Installation.

CHECK MAP SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect MAP sensor harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between MAP sensor harness connector and ground.

    + −

    Voltage

    (Approx.)
    MAP sensor
    Connector Terminal
    F86 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK MAP SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ECM harness connector and MAP sensor harness connector.

    ECM MAP sensor Continuity
    Connector Terminal Connector Terminal
    F71 80 F86 1 Existed

  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

CHECK MAP SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ECM harness connector and MAP sensor harness connector.

    ECM MAP sensor Continuity
    Connector Terminal Connector Terminal
    F71 106 F86 3 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK MAP SENSOR CIRCUIT

  1. Check the continuity between ECM harness connector and MAP sensor harness connector.

    ECM MAP sensor Continuity
    Connector Terminal Connector Terminal
    F71 120 F86 2 Existed

  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

    P0106 Manifold Absolute Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0106 00 ABSL PRES SEN/CIRC (Manifold Absolute Pressure/Barometr...
    P0111 Iat Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0111 00 IAT SENSOR 1 B1 (Intake air temperature sensor 1 circui...

    Other materials:

    Dtc/circuit Diagnosis. B1040-22 Vehicle Speed
    DTC Description DTC DETECTION LOGICNOTE: This DTC may be detected when drive the Nissan Ariya vehicle at vehicle speed of 186 MPH (300 km/h) or more. DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1040-22 Nissan Ariya Vehicle speed (Vehicle speed) ...

    Repair Information. Service Data and Specifications (sds)
    Body Alignment Body Center Marks Factory marks exist on certain parts of the body to indicate the vehicle center. When repairing the Nissan Ariya vehicle frame (members, pillars, etc.) damaged in an accident, the most accurate and effective repair will be achieved by using these marks togeth ...

    Side Radar (rear Left) (side Radar Rear Lh)
    C1e00-44 Control Unit DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1E00–44 Control unit (Control unit) Diagnosis condition When ignition switch is ON. Signal (terminal) - Threshold If sid ...