Nissan Rogue (T33) 2021-Present Service Manual: C106b-64 Stop Lamp Sw

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C106b-64 Stop Lamp Sw

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C106B 64

Stop lamp SW

(Stop lamp switch) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) CAN communication signal
Threshold When stop lamp switch signal is not input when brake pedal operates.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • CAN communication line

  • Stop lamp switch signal circuit

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • CAN communication line

  • Stop lamp switch

  • BCM

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF), and wait 10 seconds or more.

  2. Start the engine.

    NOTE:

    Stop the Nissan Ariya vehicle.

  3. Wait 1 minute or more.

    NOTE:

    Never depress brake pedal.

  4. Depress brake pedal by 100 mm (3.94 in) or more, and maintain at that position for a minimum of 1 minute or more.

  5. Release brake pedal, and wait 1 minute or more.

  6. Ignition switch OFF (Auto ACC function OFF).

  7. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  8. Perform self-diagnosis for “ABS”.

Is DTC “C106B-64” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK BCM SYSTEM

CONSULT

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK CONNECTOR AND TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect BCM harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 3.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect BCM harness connector.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF).

  6. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC “C106B-64” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

    C1061-4a Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1061 4A FR LH wheel sensor (Front left wheel sensor) Diagno...
    C106c-01 Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106C 01 Pressure sensor (Pressure sensor) Diagnosis conditi...

    Other materials:

    Nissanconnect. Preparation. Preparation
    Preparation Commercial Service Tools Tool Description Power tool Loosening screws Always Replace With New Parts Always Replace With New PartsNever Reuse These PartsPart CodeFor additional information: Washer - ROOF ANTENNA EXPLODED VIEW ...

    Led Headlamp. Service Data and Specifications (sds). Service Data and Specifications (sds)
    Service Data and Specifications (sds) Bulb Specifications Item Type Wattage (W) Headlamp Headlamp (Hi) LED — Headlamp (Lo) LED — Front combination lamp [front turn signal lamp (bulb type)] Front turn signal lamp 7444NA 28/8W Parking lamp/Daytime run ...

    Meter/m&a (combination Meter)
    B2202-11 Fuel Sender DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detected condition B2202-11 Fuel level sensor (Fuel level sensor) Diagnosis condition When ignition switch is ON. Signal (terminal) Fuel level sensor si ...