Nissan Rogue (T33) 2021-Present Service Manual: Ambient Sensor Signal Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Meter, Warning Lamp & Indicator / Type B :: Dtc/circuit Diagnosis / Ambient Sensor Signal Circuit

Diagnosis Procedure

CHECK AMBIENT SENSOR POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect ambient sensor harness connector.

  3. Ignition switch ON.

  4. Check voltage between ambient sensor harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Ambient sensor
    Connector Terminal
    E76 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK AMBIENT SENSOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between ambient sensor harness connector and ground.

    Ambient sensor — Continuity
    Connector Terminal
    E76 1 Ground Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connector.

CHECK AMBIENT SENSOR

Check ambient sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace ambient sensor. Refer to Removal and Installation.

CHECK AMBIENT SENSOR POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect combination meter harness connector.

  3. Check continuity between ambient sensor harness connector and combination meter harness connector.

    Ambient sensor Combination meter Continuity
    Connector Terminal Connector Terminal
    E76 1 M76 29 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness or connector.

CHECK AMBIENT SENSOR POWER SUPPLY CIRCUIT FOR GROUND SHORT

Check continuity between ambient sensor harness connector and ground.

Ambient sensor — Continuity
Connector Terminal
E76 2 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness or connector.

CHECK AMBIENT SENSOR POWER SUPPLY CIRCUIT FOR POWER SHORT

  1. Ignition switch ON.

  2. Check voltage between ambient sensor harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Ambient sensor
    Connector Terminal
    E76 1 Ground 0 V

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace harness or connector.

Component Inspection

CHECK AMBIENT SENSOR

  1. Remove ambient sensor. Refer to Removal and Installation.

  2. Check resistance between ambient sensor terminals.

    Terminal Condition Resistance: kΩ
    Temperature: °C (°F)
    1 2 −20 (−4) 16.50
    −10 (14) 9.92
    0 (32) 6.19
    10 (50) 3.99
    20 (68) 2.65
    25 (77) 2.19
    30 (86) 1.81
    40 (104) 1.27

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace ambient sensor. Refer to Removal and Installation.

    Fuel Level Sensor Signal Circuit
    Component Function Check PERFORM COMPONENT FUNCTION CHECK (1) Ignition switch OFF. Disconnect fuel level sensor unit, fuel pump and FPCM (fuel level sensor) (main) harness conne...
    Oil Level Sensor Signal Circuit
    DiagnosisProcedure CHECK OIL LEVEL SENSOR CIRCUIT Ignition switch OFF. Disconnect combination meter harness connector and oil level sensor harness connector. Check continuity be...

    Other materials:

    Fuel Pump
    Component Inspection CHECK FUEL PUMP Turn ignition switch OFF. Disconnect “fuel level sensor unit and fuel pump” harness connector. Check the resistance between “fuel level sensor unit and fuel pump” terminals as follows. Fuel level sensor unit and fuel pump Condition Res ...

    P0327 Ks
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0327 00 KNOCK SEN/CIRC-B1 (Knock/combustion vibration sensor 1 circuit low bank 1 or single sensor ) Diagnosis condition Engine running at idle Signal (t ...

    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 00 TP SENSOR-B1 (Throttle/Pedal ...