Nissan Rogue (T33) 2021-Present Service Manual: U2248-83 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Transmission & Driveline :: Driveline / Transfer: Ty92a :: Dtc/circuit Diagnosis / U2248-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detecting condition
U2248-83

CAN comm err (brake control unit)

[Controller area network communication error (brake control unit)] 		Diagnosis condition Ignition switch: ON
Signal CAN communication signals
Threshold CAN signal from ABS actuator and electric unit (control unit) is unmatched between CAN signal and calculated value. (Due to noise on CAN)
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

Although AWD control is canceled, the vehicle can drive at 2WD condition.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h (6 MPH) or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Ariya vehicle.

  4. Perform "Self diagnosis result" mode of “AWD/4WD”.

Is DTC “U2248-83” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

CONSULT

Perform "Self diagnosis result" mode of “ABS”.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After placing the ignition switch OFF, perform DTC confirmation procedure again. If DTC “U2248-83” is detected, replace actuator assembly due to the malfunction of the AWD control unit. Refer to Disassembly and Assembly.

NO>>

Repair or replace error-detected parts.

    U2176-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition U2176-87 CAN comm err (CCM) [Controller area network communicati...
    U2248-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition U2248-87 CAN comm err (brake control unit) [Controller area netw...

    Other materials:

    Towing load/specification
    WARNING The towing capacities in this manual are general guidelines. Actual safe towing capacity of your Nissan Rogue depends on factory or dealer-installed equipment, passenger load, and cargo weight. You must weigh both the vehicle and trailer as described to determine true towing capacity. Never ...

    P1c90-49 Sub Starter & Generator
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1C90-49 Sub starter & generator (Sub starter & generator) Diagnosis condition Engine running at idle Signal (terminal) - Threshold Sub starte ...

    C106f-54 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106F 54 Steering angle sensor (Steering angle sensor) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. ...