Nissan Rogue (T33) 2021-Present Service Manual: U2248-87 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Transmission & Driveline :: Driveline / Transfer: Ty92a :: Dtc/circuit Diagnosis / U2248-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detecting condition
U2248-87

CAN comm err (brake control unit)

[Controller area network communication error (brake control unit)] 		Diagnosis condition Ignition switch: ON
Signal CAN communication signals
Threshold Not receiving CAN signal from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

Although AWD control is canceled, the vehicle can drive at 2WD condition.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h (6 MPH) or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Ariya vehicle.

  4. Perform "Self diagnosis result" mode of “AWD/4WD”.

Is DTC “U2248-87” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

CONSULT

Perform "Self diagnosis result" mode of “ABS”.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After placing the ignition switch OFF, perform DTC confirmation procedure again. If DTC “U2248-87” is detected, replace actuator assembly due to the malfunction of the AWD control unit. Refer to Disassembly and Assembly.

NO>>

Repair or replace error-detected parts.

    U2248-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition U2248-83 CAN comm err (brake control unit) [Controller area netw...
    U3d02-06 Incomplete Programming
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition U3D02-06 INCOMP PROGRAMMING (Incomplete programming) Diagnosis c...

    Other materials:

    Dtc/circuit Diagnosis. U0075-00 Communication Bus C Off
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U0075-00 Control module comm Bus C Off (Control module communication Bus C Off) Diagnosis condition Ignition switch ON Signal (terminal) CAN communication s ...

    Towing load/specification
    WARNING The towing capacities in this manual are general guidelines. Actual safe towing capacity of your Nissan Rogue depends on factory or dealer-installed equipment, passenger load, and cargo weight. You must weigh both the vehicle and trailer as described to determine true towing capacity. Never ...

    Main Line Between Lib 12v and M&a Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). Harness connector B41 Harness con ...