Nissan Rogue (T33) 2021-Present Service Manual: U218b-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U218B 87 CAN communication error [12V sub battery (Lithium ion battery)] Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold Not receiving from 12V sub battery (Lithium ion battery).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • 12V sub battery (Lithium ion battery)

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U218B-87” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U218B-87” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK 12V SUB BATTERY (LITHIUM ION BATTERY) SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “Lithium ion battery 12V”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “Lithium ion battery 12V”.

Is DTC detected?

YES>>

Check the DTC.

NO>>

GO TO 3.

CHECK 12V SUB BATTERY (LITHIUM ION BATTERY) SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect 12V sub battery (Lithium ion battery) harness connector.

  3. Check 12V sub battery (Lithium ion battery) harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect 12V sub battery (Lithium ion battery) harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U218b-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U218B 83 CAN communication error [12V sub battery (Lithium ion battery)] Diagnosis condi...
    U2248-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2248 83 CAN communication error [ABS actuator and electric unit (control unit)] Diagnos...

    Other materials:

    Dtc/circuit Diagnosis. B100e-1a Knee Air Bag Module Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B100E-1A Knee air bag module RH (Knee air bag module right hand) Diagnosis condition When ignition switch is ON. Signal (terminal) Knee air bag module RH si ...

    Dtc/circuit Diagnosis. C1731-16 Tire Pressure Sensor Fl
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure reported by the TPMS sensor Read TPMS DTCs ...

    Tcm
    Reference Value CONSULT DATA MONITOR STANDARD VALUE In CONSULT, electric shift timing or lock-up timing, i.e. operation timing of each solenoid valve, is displayed. Therefore, if there is an obvious difference between the shift timing estimated from a shift shock (or engine speed variation ...