Nissan Rogue (T33) 2021-Present Service Manual: U218b-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U218B 83 CAN communication error [12V sub battery (Lithium ion battery)] Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold 12V sub battery (Lithium ion battery) in malfunctioning.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • 12V sub battery (Lithium ion battery)

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U218B-83” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U218B-83” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK LI-ION BATTERY CONTROLLER SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “Lithium ion battery 12V”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “Lithium ion battery 12V”.

Is DTC detected?

YES>>

Check the DTC.

NO>>

GO TO 3.

CHECK 12V SUB BATTERY (LITHIUM ION BATTERY) SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect 12V sub battery (Lithium ion battery) harness connector.

  3. Check 12V sub battery (Lithium ion battery) harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect 12V sub battery (Lithium ion battery) harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2165-57 Mac Comm Error (sonar Control Unit)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2165 57 CAN communication error (sonar control unit) Diagnosis condition — Signal (te...
    U218b-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U218B 87 CAN communication error [12V sub battery (Lithium ion battery)] Diagnosis condi...

    Other materials:

    Dtc/circuit Diagnosis. U0075-00 Communication Bus C Off
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U0075-00 Control module comm Bus C Off (Control module communication Bus C Off) Diagnosis condition Ignition switch ON Signal (terminal) CAN communication s ...

    Reporting safety defects
    For USA If you believe that your vehicle has a defect that could cause a crash or lead to injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN. This applies whether you drive a Nissan Rogue or another NISSAN model. ...

    Brake fluid
    For more information on brake fluid type and capacity, refer to “Capacities and recommended fluids/lubricants”. WARNING Always use new brake fluid from a sealed container. Contaminated, old, or poor-quality fluid may damage the brake system and reduce stopping performance. Clean the filler c ...