Nissan Rogue (T33) 2021-Present Service Manual: U1cf9 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / U1cf9 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U1CF9 00

Lost communication with VDC in secondary ECU

(Lost communication with VDC in secondary ECU) 		Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold ECM is not receiving CAN communication signal other than OBD (emission related diagnosis).
Diagnosis delay time 30 seconds or more

POSSIBLE CAUSE

  • Harness or connectors (CAN communication line is open or shorted)

  • ABS actuator and electric unit

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC U1CF9 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Proceed to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON and wait at least 3 seconds.

  2. Check 1st trip DTC.

Is DTC U1CF9 detected?

YES>>

Refer toDTC Diagnosis Procedure .

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC U1CF9 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Proceed to DTC Description.

NO>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

    U1cf8 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CF8 00 Lost communication with ECM in secondary ECU (Lost comm...
    U1cfa Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CFA 00 Lost communication with USM in secondary ECU (Lost comm...

    Other materials:

    B3a70 Intelligent Battery Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition B3A70 00 IBS Battery Temp Sensor Failure (Open Circuit) [IBS battery temp sensor failure (Open circuit)] Diagnosis condition Ignition switch ON Batte ...

    Dtc/circuit Diagnosis. B2010-1c Battery Voltage
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2010-1C Battery voltage (Battery voltage) Diagnosis condition All times Signal (terminal) Intelligent Key unit battery power supply signal Threshold ...

    P00fe Evap Control System
    DTC Description This diagnosis detects clogs in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve.ECM controls EVAP control system as below. ECM monitors EVAP line pressure change to diagnose if there is no clogging between EVAP canister and fuel tank. E ...