Nissan Rogue (T33) 2021-Present Service Manual: U1cf8 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / U1cf8 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U1CF8 00

Lost communication with ECM in secondary ECU

(Lost communication with ECM in secondary ECU ) 		Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold eVTC is not receiving CAN communication signal with ECM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication line between eVTC and ECM( CAN communication line is open or short)

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC U1CF8 is displayed with DTC U2384, first perform the confirmation procedure (trouble diagnosis) for DTC U2384.

Is DTC U2384 detected?

YES>>

Proceed to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON and wait at least 3 seconds.

  2. Check 1st trip DTC.

Is DTC U1CF8 detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC U1CF8 is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

    U1327 Mac Key
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1327 52 MAC Key update (MAC Key update) Diagnosis condition —...
    U1cf9 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CF9 00 Lost communication with VDC in secondary ECU (Lost comm...

    Other materials:

    U2340-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U2340-87 CAN communication error (ECM) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold Lost communication with ECM Diagnosi ...

    Service Data and Specifications (sds)
    Road Wheel ALUMINUM WHEEL Item Limit Runout Axial runout Less than 0.3 mm (0.012 in) Radial runout Allowable unbalance Dynamic (At flange) Less than 5 g (0.17 oz) (one side) Static (At flange) Less than 10 g (0.35 oz) STEEL WHEEL (EMERGENCY) Item Limit Runo ...

    Periodic Maintenance. Wheel Alignment
    Inspection DESCRIPTIONMeasure wheel alignment under unladen conditions.NOTE: “Unladen conditions” means that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. PRELIMINARY CHECKCheck the following: Tires for improper air pre ...