Nissan Rogue (T33) 2021-Present Service Manual: U1327-52 Mac Key
Without Propilot Assist 2.1
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| U1327 | 52 |
MAC key update (Message Authentication Code key update) |
Diagnosis condition | — |
| Signal (terminal) | — | |||
| Threshold | MAC key writing is incomplete | |||
| Diagnosis delay time | — | |||
POSSIBLE CAUSE
-
Network communication error between CONSULT and ADAS control unit 2
-
ADAS control unit 2 used in other Nissan Ariya vehicles is installed in the vehicle
-
ADAS control unit 2
FAIL-SAFE
The following systems are canceled.
-
Vehicle-to-vehicle distance control mode
-
Conventional (fixed speed) cruise control mode
-
Steering wheel assistance function
-
AEB
-
RAB
-
I-FCW
-
LDW
-
I-LI
-
BSW
-
I-BSI
-
RCTA
-
TSR
-
I-DA
CONFIRMATION PROCEDURE
CHECK DTC PRIORITY
If DTC “U1327-52” is displayed with DTC “U1327-54”, first perform the trouble diagnosis for DTC “U1327-54”.
Is applicable DTC detected?
YES>>Refer to DTC Description.
NO>>GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
-
Ignition switch ON.
-
Perform “MAC key writing”. Refer to Work Procedure.
-
Perform “MAC Diagnosis” of “ICC/ADAS 2” using CONSULT.
Is DTC “U1327-52” detected as the current malfunction?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
With Propilot Assist 2.1
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| U1327 | 52 |
MAC key update (Message Authentication Code key update) |
Diagnosis condition | — |
| Signal (terminal) | — | |||
| Threshold | MAC key writing is incomplete | |||
| Diagnosis delay time | — | |||
POSSIBLE CAUSE
-
Network communication error between CONSULT and ADAS control unit 2
-
ADAS control unit 2 used in other Nissan Ariya vehicles is installed in the vehicle
-
ADAS control unit 2
FAIL-SAFE
None
CONFIRMATION PROCEDURE
CHECK DTC PRIORITY
If DTC “U1327-52” is displayed with DTC “U1327-54”, first perform the trouble diagnosis for DTC “U1327-54”.
Is applicable DTC detected?
YES>>Refer to DTC Description.
NO>>GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
-
Ignition switch ON.
-
Perform “MAC key writing”. Refer to Work Procedure.
-
Perform “MAC Diagnosis” of “ICC/ADAS 2” using CONSULT.
Is DTC “U1327-52” detected as the current malfunction?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK DTC PRIORITY
If DTC “U1327-52” is displayed with DTC “U1327-54”, first perform the trouble diagnosis for DTC “U1327-54”.
Is applicable DTC detected?
YES>>Refer to DTC Description.
NO>>GO TO 2.
PERFORM MAC KEY WRITING
With CONSULT
-
Perform “MAC key writing”. Refer to Work Procedure.
-
Perform “MAC Diagnosis” of “ICC/ADAS 2” using CONSULT.
Is DTC “U1327-52” detected as the current malfunction?
YES>>Replace the ADAS control unit 2. Refer to Removal and Installation.
NO>>INSPECTION END.
Other materials:
Diagnosis System (bcm)
Common Item
CONSULT Function (BCM - COMMON ITEM)
BCM
Refer to CONSULT Function (BCM - COMMON ITEM).
Flasher
CONSULT Function (BCM - FLASHER)
BCM
Refer to CONSULT Function (BCM - FLASHER).
...
Brake assist
Brake assist
When brake pedal force exceeds a certain
threshold, Brake Assist activates to provide
greater braking force than a conventional
brake booster, even with relatively light pedal
pressure.
WARNING
Brake Assist supports braking but does
not replace careful driving. It is not a collision
wa ...
Rear Propeller Shaft: Cvj-Cvj-C. Periodic Maintenance. Rear Propeller Shaft
Rear Propeller Shaft
Inspection
LOOSENESS OF CONNECTED PARTCheck each fixing bolt and nut for looseness using torque wrench. For each tightening torque, refer to Exploded View.BACKLASH OF JOINT PARTMove
the joint of propeller shaft up and down and from side to side (axial
direction of shaft an ...
