Nissan Rogue (T33) 2021-Present Service Manual: U012e Can Communication

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / U012e Can Communication

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U012E 00

Communication error (lost)

(Lost communication with camshaft position control module) 		Diagnosis condition Engine running at idle
Signal (terminal) CAN communication signal
Threshold Internal error of the electric intake valve timing control module is detected.
Diagnosis delay time —

POSSIBLE CAUSE

  • Electric Intake valve timing control module

  • ECM

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

or

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted. always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle for at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION LINE

Perform trouble diagnosis of CAN communication system. Refer to Trouble Diagnosis Flow Chart.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

REPLACE ELECTRIC INTAKE VALVE TIMING CONTROL MODULE

  1. Replace electric intake valve timing control module. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC U012E detected again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    U0120 Can Communication
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0120 00 STR/GEN C/M (Lost Communication With Starter / Generato...
    U0131can Communication
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0131 00 Lost communication (EPS C/U) (Lost Communication With P...

    Other materials:

    Simplified Confirmation by Birds-Eye View Screen
    Work Procedure If the front grille upper is removed or replaced, perform the simplified confirmation by birds-eye view screen.CAUTION: This procedure should only be performed if the front grille upper has been removed or replaced. Perform camera calibration when removing or replacing each ...

    Symptom Diagnosis. Automatic Back Door Anti-Pinch Function Does Not Operate
    Diagnosis Procedure CHECK DTC WITH AUTOMATIC BACK DOOR CONTROL UNIT Check that DTC is not detected with automatic back door control unit. Is the inspection result normal? YES>> GO TO 2. NO>> Refer to DTC Index. CHECK TOUCH SENSOR LH Check touch sensor LH. Refer to DTC Diagnos ...

    Dtc/circuit Diagnosis. B2416-15 Touch Sensor Circuit Rh Open
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2416-15 Touch sensor circuit RH open (Touch sensor circuit right hand open) Diagnosis condition All times Signal (terminal) Touch sensor RH signal Thr ...