Nissan Rogue (T33) 2021-Present Service Manual: U0079-00 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Audio, Visual & Navigation System / Telematics System :: Dtc/circuit Diagnosis / U0079-00 Can Comm Circuit

DTC Description

DESCRIPTION

CAN (Controller Area Network) is a serial communication line for real-time application. It is an onNissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Ariya vehicle, and each control unit shares information and links with other control units during operation (not independently). In CAN communication, control units are connected with 2 communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U0079-00

Control module comm Bus G Off

(Control module communication bus "G" off) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Transmission or reception error
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

Telematics system does not operate

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “IVC” using CONSULT.

  5. Check DTC.

Is DTC U0079-00 detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM CONFIRMATION PROCEDURE

WITH CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Turn ignition switch OFF and wait at least 30 seconds.

  4. Turn ignition switch ON and wait at least 2 seconds or more.

  5. Select “Self Diagnostic Result” mode of “MULTI AV” using CONSULT.

  6. Check DTC.

Is DTC "U0079–00" detected?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to CAN Communication Signal Chart.

NO>>

INSPECTION END

    U0074-00 Av Communication
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0074-00 Control module comm Bus B Off (Control module commu...
    U2141-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2141–87 CAN comm err (TCM) [Controller area network commu...

    Other materials:

    Symptom Diagnosis. Low Tire Pressure Warning Lamp Does Not Turn Off
    Description The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts. Diagnosis Procedure CHECK TIRE PRESSURE Ignition switch ON. CAUTION: Never start the engine. Check the tire pressure for all wheels and adjust to the specified value ...

    Automatic Brake Hold. Removal and Installation
    Chassis Control Module Removal and Installation Removal and installation procedure of chassis control module. Refer to Removal and Installation. Automatic Brake Hold Switch Removal and Installation Removal and installation procedure of parking brake switch. Refer to Removal and Installation.NOTE: ...

    P044a Egr Volume Contro Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P044A 00 EGR SENSOR C (EGR sensor C circuit low) Diagnosis condition Ignition switch ON Signal (terminal) EGR volume control valve signal Threshol ...