Nissan Rogue (T33) 2021-Present Service Manual: Precaution :: Precautions

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collisions.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” sections of this Service Manual.

WARNING:

Always observe the following items for preventing accidental activation:

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation:

Precautions for Removing Battery Terminal

• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the Intelligent Key or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even after the ignition switch is in the OFF position, i.e. ACC power is supplied for a certain fixed time.

• When disconnecting the 12V battery terminal, place the ignition switch in the OFF position before disconnecting the 12V battery terminal, observing “How to disconnect 12V battery terminal” described below.

  

  NOTE:

  Some ECUs operate for a certain fixed time even after ignition switch is in the OFF position and ignition power supply is stopped. If the battery terminal is disconnected before ECU stops, accidental DTC detection or ECU data damage may occur.

• For Nissan Ariya vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before placing the ignition switch in the ON position.

  NOTE:

  If the ignition switch is in the ON position with any one of the terminals of main battery and sub battery disconnected, then DTC may be detected.

• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

  NOTE:

  The removal of 12V battery may cause a DTC detection error.

HOW TO DISCONNECT 12V BATTERY TERMINAL

Disconnect 12V battery terminal according to instruction described below.

1. Open the hood.

2. Place the ignition switch in the ON position.

3. Place the ignition switch in the OFF position with the driver side door opened.

4. Get out of the Nissan Ariya vehicle and close the driver side door.

5. Wait at least 3 minutes.

   CAUTION:

   While waiting, never operate the Nissan Ariya vehicle such as locking, opening, and closing doors. Violation of this caution results in the activation of ACC power supply according to the Auto ACC function.

6. Remove 12V battery terminal.

   CAUTION:

   After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.

Precaution for Parking Brake System

WARNING:

Since dust covering the rear brakes has an affect on human body, the dust must be removed with a dust collector. Never splatter the dust with an air blow gun.

• When the parking brake is operated, the electric parking brake indicator lamp in the combination meter and the parking brake switch indicator turn ON.

• When a following malfunction occurs in the electric parking brake system, the electric parking brake warning lamp turn ON, electric parking brake indicator lamp turn ON/OFF (depends on the electric parking brake system) or blink, and parking brake switch indicator turn blink.

  • When a status cannot be judged between applied and released.

  • When the parking brake switch is operated under the condition that the parking brake switch is malfunction.

  • When the parking brake switch is operated under the condition that the parking brake actuator is malfunction.

  • When the initial position adjustment of the parking brake actuator is incomplete.

  • When a parking brake system mode is factory mode

    CAUTION:

    When Nissan Ariya vehicle is parked, electric shift selector is in the P position.

• When a malfunction occurs in the electric parking brake system, parking brake can be mechanically released. Refer to Work Procedure.

• When parking brake must be released while the 12V battery negative terminal is disconnected, mechanically release it. Refer to Work Procedure.

• When rear brake pad is ground or replaced, perform break-in operation. Refer to Inspection and Adjustment.

• When rear disc rotor is ground or replaced, perform break-in operation. Refer to Inspection and Adjustment.

Precaution for Harness Repair

• Solder the repair part, and wrap it with tape. [Twisted wire fray must be 110 mm (4.33 in) or less.]

  

• Never bypass the repair point with wire. (If it is bypassed, the turnout point cannot be separated and the twisted wire characteristics are lost.)