Nissan Rogue (T33) 2021-Present Service Manual: Power Supply and Ground Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Manual Air Conditioning :: Dtc/circuit Diagnosis / Power Supply and Ground Circuit

A/c Amp.

Diagnosis Procedure

CHECK A/C AMP. GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect A/C amp. connector.

  3. Check continuity between A/C amp. harness connector and ground.

    A/C amp. (–) Continuity
    Connector Terminal
    M55 58 Ground Yes

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK FUSE

Check that the following fuse is not blown (open).

Unit Location Fuse No. Capacity
A/C amp. Fuse block (J/B) 40 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK A/C AMP. POWER SUPPLY

  1. Connect A/C amp. connector.

  2. Check voltage between A/C amp. harness connector terminals.

    A/C amp. Condition Voltage
    Connector Terminal
    (+) (−)
    M55 60 58 Ignition switch OFF (auto ACC status) or ON Battery voltage
    Ignition switch OFF (not auto ACC status) 0 V

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair the A/C amp. power supply circuit.

A/c Switch Assembly

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open).

    Unit Location Fuse No. Capacity
    A/C switch assembly Fuse block (J/B) 40 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK A/C SWITCH ASSEMBLY POWER SUPPLY

  1. Disconnect A/C switch assembly connector.

  2. Ignition switch ON.

  3. Check voltage between A/C switch assembly harness connector and ground.

    (+) (−) Voltage
    A/C switch assembly
    Connector Terminal
    M84 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector between A/C switch assembly and fuse.

CHECK A/C SWITCH ASSEMBLY GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Check continuity between A/C switch assembly harness connector and ground.

    A/C switch assembly (–) Continuity
    Connector Terminal
    M84 6 Ground Yes

Is the inspection result normal?

YES>>

Replace A/C switch assembly. Refer to Removal and Installation.

NO>>

Repair harness or connector.

    U2140-87 Can Comm Err (ecm)
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line...
    Door Motor
    Diagnosis Procedure NOTE: If all of door motor DTCs are detected, check this circuit. CHECK DOOR MOTOR POWER SUPPLY Ignition switch ON. Check voltage between intake door motor h...

    Other materials:

    Preparation
    Special Service Tool The actual shapes of TechMate tools may differ from those of special service tools illustrated here. Tool number (TechMate No.) Tool name   Description (NI-39570) Chassis ear Locates the noise (NI-50397) NISSAN Squeak and Rattle Kit Repairs ...

    Precaution. Precautions
    PRECAUTIONS FOR SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG AND SEAT BELT PRE-TENSIONER : Precautions The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury t ...

    Unit Disassembly and Assembly. Steering Gear and Linkage
    Exploded View DISASSEMBLY (NORTH AMERICA PRODUCTION MODELS)DISASSEMBLY (JAPAN PRODUCTION MODELS) Outer socket Outer socket lock nut Boot clamp (small diameter) Boot Boot clamp (large diameter) Hole cover seal Gear housing assembly         ...