Nissan Rogue (T33) 2021-Present Service Manual: P2566 Wastegate Control Valve Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2566 Wastegate Control Valve Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2566 00

TC BOOST CONTROL POSITN SEN A

(Turbocharger boost control position sensor A circuit intermittent) 		Diagnosis condition

  • Battery voltage: 8 V or more

  • Ignition switch: ON
Signal (terminal) —
Threshold An excessively low voltage from the wastegate control valve position sensor is sent to the ECM.
Diagnosis delay time 1 seconds

POSSIBLE CAUSE

  • Harness or connectors

    (Wastegate control valve position sensor circuit is open or shorted.)

  • Electric wastegate control actuator

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Ariya vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h (44 MPH) or more is possible.

NOTE:

This value is a reference value converted from engine power to Nissan Ariya vehicle speed. Actual power limitation value differs due to the malfunctioning part and driving condition.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P2566 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle for 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P2566 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect electric wastegate control actuator harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between electric wastegate control actuator harness connector and ground.

    + −

    Voltage

    (Approx.)
    Electric wastegate control actuator
    Connector Terminal
    F95 4 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between electric wastegate control actuator harness connector and ECM harness connector.

    Electric wastegate control actuator ECM Continuity
    Connector Terminal Connector Terminal
    F95 2 F71 111 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between electric wastegate control actuator harness connector and ECM harness connector.

    Electric wastegate control actuator ECM Continuity
    Connector Terminal Connector Terminal
    F95 3 F71 75 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

Check the electric wastegate control actuator. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace electric wastegate control actuator. Refer to ComponentPartsLocation.

    P2565 Wastegate Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2565 00 TC BOOST CONTROL POSITN SEN A (Turbocharger boost contr...
    P2610 Ecm Internal Timer
    DTC Description DESCRIPTIONThis ECM contains a timer and measures time between an ignition switch OFF and the next ignition switch ON. This enables the judging of the state of e...

    Other materials:

    Dtc/circuit Diagnosis. Door Lock/unlock Switch
    Front Lh Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Door lock and unlock switch (lock)”, “Door lock and unlock switch (unlock)” in “Data monitor” mode of "BCM [INT LAMP]". Check that the function operates normally according to the follow ...

    RearView Monitor
    Basic information CAMERA button WARNING Failure to follow the warnings and usage instructions for the RearView Monitor in your Nissan Rogue can result in serious injury or death. The RearView Monitor is a driver-assist tool, not a replacement for safe driving habits. Always turn your head, ...

    P025b Fuel Pump Module a
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P025B 00 FUEL PUMP MODULE A (Fuel Pump Module "A" Control Circuit Range/Performance) Diagnosis condition Engine running Signal (terminal) — Thre ...