Nissan Rogue (T33) 2021-Present Service Manual: P2610 Ecm Internal Timer

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2610 Ecm Internal Timer

DTC Description

DESCRIPTION

This ECM contains a timer and measures time between an ignition switch OFF and the next ignition switch ON. This enables the judging of the state of engine cooling at an engine start.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2610 00

ECM/PCM INTERNAL ENG OFF TIMER

(ECM/PCM engine off timer performance) 		Diagnosis condition —
Signal (terminal) —
Threshold

  • ECM internal engine off timer is malfunctioning

  • The time calculated by ECM based on a descent allowance of engine coolant temperatures during ignition switch OFF is extremely shorter than the time counted by the Engine internal OFF timer
Diagnosis delay time —

POSSIBLE CAUSE

  • ECM

  • ECM power supply

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

INSPECTION START

It is necessary to erase permanent DTC?

YES>>

GO TO 4.

NO>>

GO TO 2.

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 12 V or more under ignition switch OFF condition.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-I

  1. Turn ignition switch ON and wait at least 190 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

DTC Diagnosis Procedure

NO>>

INSPECTION END

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is 12 V or more under ignition switch OFF condition.

  • Before performing the following procedure, check that fuel level is between 2/8 and 7/8.

>>

GO TO 5.

PERFORM DTC CONFIRMATION PROCEDURE-I

  1. Turn ignition switch ON and wait at least 190 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

GO TO 6.

PERFORM DTC CONFIRMATION PROCEDURE-II

CAUTION:

To start this self-diagnosis, the conditions listed bellow are required to be satisfied. Perform the following steps to satisfy the conditions.

  • Engine coolant temperature decrease by 55°C (131°F) or more during the time between an ignition switch OFF (after engine warm-up) and the second ignition switch ON.

  • A fuel temperature at the second ignition switch ON is −5°C (23°F) or more and less than 35°C (95°F).

  • The temperature difference between engine coolant and fuel is 5°C (41°F) or more.

NOTE:

This self-diagnosis is not performed if the distance traveled is extremely short.

  1. Turn ignition switch ON.

  2. Start engine and warm it up to normal operating temperature.

  3. Turn ignition switch OFF and soak the Nissan Ariya vehicle for at least 12 hours.

    CAUTION:

    • Never turn ON the ignition switch during soaking.

    • Never open the fuel filler cap and perform refueling during soaking.

  4. Turn ignition switch ON and wait at least 190 seconds.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Check ECM power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK SELF-DIAGNOSTIC RESULT

Check that DTCs related to the fuel system and the cooling system are not detected.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Erase DTC.

  2. Perform DTC Confirmation Procedure again. Refer to DTC Description.

Is the 1st trip DTC P2610 displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P2566 Wastegate Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2566 00 TC BOOST CONTROL POSITN SEN A (Turbocharger boost c...
    P2614 Intake Camshaft Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2614 00 A camshaft posi signal B1 (Camshaft A Position Signal O...

    Other materials:

    Limites du système LDW
    AVERTISSEMENT Les limites du système LDW du Nissan Rogue sont décrites ci-dessous. Le non-respect des instructions et avertissements relatifs à l’utilisation correcte du système LDW peut entraîner des blessures graves, voire mortelles. Le système LDW ne fonctionne pas lorsque la vites ...

    P1536 Ascd System
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1536 00 Cruise control (Cruise control) Diagnosis condition Ignition switch ON Signal CAN communication signal Threshold ECM cannot receive a ...

    System Description. System. Warning/indicator/chime List
    Warning/indicator/chime List Warning Lamp/Indicator Lamp/Information display Warning lamp Item Design Reference Seat belt warning lamp For layout, refer to Design. For function, refer to Seat Belt Warning Lamp. Information display Item Reference Rear seat belt warning Ref ...