Nissan Rogue (T33) 2021-Present Service Manual: P2484 Exhaust Gas Temperature Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2484 Exhaust Gas Temperature Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2484 00

Exhaust gas temp sensor bank 1

(Exhaust Gas Temperature Sensor Circuit Intermittent/Erratic Bank 1 Sensor 5) 		Diagnosis condition Engine run
Signal (terminal) Exhaust gas temperature signal
Threshold ECM detects exhaust gas temperature sensor circuit is opened.
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Exhaust gas temperature sensor

  • Harness or connectors

    (Exhaust gas temperature sensor circuit is short.)

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to normal operating temperature.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK EXHAUST GAS TEMPERATURE SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect exhaust gas temperature sensor harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between exhaust gas temperature sensor harness connector and ground.

    + −

    Voltage

    (Approx.)
    Exhaust gas temperature sensor
    Connector Terminal
    E26 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK EXHAUST GAS TEMPERATURE SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.

    + − Continuity
    Exhaust gas temperature sensor ECM
    Connector Terminal Connector Terminal
    E26 2 F71 99 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST GAS TEMPERATURE SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.

    + − Continuity
    Exhaust gas temperature sensor ECM
    Connector Terminal Connector Terminal
    E26 1 F71 113 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST GAS TEMPERATURE SENSOR

Check the exhaust gas temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace exhaust gas temperature sensor. Refer to Component Parts Location.

    P2483 Exhaust Gas Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2483 00 Exhaust gas temp sensor bank 1 (Exhaust Gas Temperature...
    P2562 Wastegate Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2562 00 TC BOOST CONTROL POSITN SEN A (Turbocharger boost c...

    Other materials:

    Dtc/circuit Diagnosis. Power Supply and Ground Circuit
    Moonroof Motor Assembly Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuse is not blown (open): Fuse No. Capacity 31 15 A Is the fuse blown (open)? YES>> Repair the blown (open) fuse after repairing the affected circuit if a fuse ...

    System Description. System (back Door Opener System)
    System Description SYSTEM DIAGRAM Component Function Back door opener switch Refer to Back Door Opener Switch. Back door opener actuator Refer to Back Door Lock Assembly. ABS actuator and electric unit (control unit) Transmit Nissan Ariya vehicle speed signal to BCM via CAN c ...

    Nissanconnect. Basic Inspection
    Diagnosis and Repair Workflow Nissanconnect Work Flow OVERALL SEQUENCEDETAILED FLOWINTERVIEW FOR MALFUNCTION It is also important to clarify the customer concerns before starting the inspection. Interview the customer about the concerns carefully and understand the symptoms fully. NOTE: ...