Nissan Rogue (T33) 2021-Present Service Manual: P2128 App Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2128 App Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2128 00

APP SEN 2/CIRC

(Throttle/Pedal position sensor/switch E circuit high) 		Diagnosis condition Engine running at idle
Signal (terminal) Accelerator pedal position sensor 2 signal
Threshold An excessively high voltage is sent to ECM
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • APP sensor 2 circuit is open or shorted.

    • Sensor power supply 2 circuit is shorted.

  • Accelerator pedal position sensor (APP sensor 2)

  • Sensor power supply 2 circuit

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK APP SENSOR 2 POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect accelerator pedal position (APP) sensor harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between APP sensor harness connector and ground.

    + −

    Voltage

    (Approx.)
    APP sensor
    Connector Terminal
    E25 2 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Refer to DTC Diagnosis Procedure.

Is inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK APP SENSOR 2 GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between APP sensor harness connector and ECM harness connector.

    + − Continuity
    APP sensor ECM
    Connector Terminal Connector Terminal
    E25 6 E21 152 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT

  1. Check the continuity between APP sensor harness connector and ECM harness connector.

    + − Continuity
    APP sensor ECM
    Connector Terminal Connector Terminal
    E25 1 E21 151 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts

CHECK APP SENSOR

Check the APP sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace accelerator pedal assembly. Refer to Removal and Installation.

    P2127 App Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2127 00 APP SEN 2/CIRC (Throttle/Pedal position sensor/switch E...
    P212b Admission Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P212B 00 Throttle position sensor/switch (Throttle Position Sens...

    Other materials:

    P00f2 Maf Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P00F2 00 Humidity Sensor Circuit/Open (Humidity Sensor Circuit/Open) Diagnosis condition — Signal (terminal) Humidity sensor　signal Threshold ...

    Dtc/circuit Diagnosis. U2a06-88 Comm Bus Off V-Fd
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped ...

    B2e32-11 Av Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E32-11 Audio unit (Audio unit) Diagnosis condition When ignition switch is ON Signal (terminal) Sound signal Threshold 0.5 V or less Diagnosi ...