Nissan Rogue Service Manual: P1715 input speed sensor
Description
ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control.
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detecting conditio |
| P1715 | IN PULY SPEED (IN PULY SPEED) | Input speed sensor signal is different from the theoretical value calculated by ECM from output speed sensor signal and engine rpm signal. |
POSSIBLE CAUSE
- Harness or connectors (The CAN communication line is open or shorted.)
- Harness or connectors (Input speed sensor circuit is open or shorted.)
- TCM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".
NO >> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
- Turn ignition switch OFF and wait at least 10 seconds.
- Turn ignition switch ON.
- Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
- Start engine and drive the vehicle at more than 50 km/h (31 MPH)
for at least 5 seconds.
CAUTION: Always drive vehicle at a safe speed.
- Check 1st trip DTC.
Is 1st trip DTC detected? YES >> Proceed to EC-416, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".
NO >> GO TO 2.
2.CHECK DTC WITH TCM
Check DTC with TCM. Refer to TM-47, "CONSULT Function".
Is the inspection result normal? YES >> GO TO 3.
NO >> Perform trouble shooting relevant to DTC indicated.
3.REPLACE TCM
Replace TCM. Refer to TM-202, "Removal and Installation".
>> INSPECTION END
P1574 ASCD vehicle speed sensor
Description
The ECM receives two vehicle speed sensor signals via CAN communication line.
One is sent from combination
meter, and the other is from TCM (Transmission control module). The ECM uses ...
P1805 brake switch
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1805
BRAKE SW/CIRCUIT
(BRAKE SW/CIRCUT)
A stop ...
Other materials:
Preparation
Special Service Tool
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-39570)
Chassis Ear
Locating the noise
—
(J-50397)
NISSAN Squeak and Rattle Kit
...
System
INTERIOR ROOM LAMP CONTROL SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM : System Description
SYSTEM DIAGRAM
OUTLINE
Interior room lamps* are controlled by interior room lamp timer control
function of BCM.
*: Map lamp and room lamp (when map lamp switch and room lamp switch are in
...
System
EPS SYSTEM
EPS SYSTEM : System Description
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL
Communicates the signal from each control unit via CAN communication.
Control unit
Signal status
ECM
Transmits the following signal to EPS control unit via CAN
communica ...
