Nissan Rogue (T33) 2021-Present Service Manual: P1574 Propilot Assist Vehicle Speed Sensor
DTC Description
The ECM receives two ProPILOT Assist vehicle speed sensor signals via CAN communication line. One is sent from combination meter, and the other is from TCM (tramsmission control module). The ECM uses these signals for ProPILOT Assist control. Refer to System Description.
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | ||
| P1574 | 00 |
ASCD VHL SPD SEN (ASCD VHL SPD SEN) |
Diagnosis condition | Nissan Ariya Vehicle speed: More than 40 km/h (25 MPH) |
| Signal (terminal) | — | |||
| Threshold | ProPILOT Assist Nissan Ariya vehicle speed signals are out of the specified range | |||
| Diagnosis delay time | — | |||
POSSIBLE CAUSE
-
Harness or connectors (CAN communication line is open or shorted.)
-
Combination meter
-
Wheel sensor
-
ABS actuator and electric unit (control unit)
-
TCM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
CHECK DTC PRIORITY
If DTC P1574 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Index.
NO>>GO TO 2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
-
Ignition switch OFF and wait at least 10 seconds.
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 10 seconds.
>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine.
-
Drive the Nissan Ariya vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the Nissan Ariya vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.
-
Check DTC.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK DTC PRIORITY
If DTC P1574 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Index.
NO>>GO TO 2.
CHECK DTC WITH TCM
Check DTC with TCM. Refer to DTC Index.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Perform trouble shooting relevant to DTC indicated.
CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Check DTC with ABS actuator and electric unit (control unit). Refer to DTC Index.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Perform trouble shooting relevant to DTC indicated.
CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to DTC Index (Full TFT meter) or DTC Index (7 inch information display).
>>
INSPECTION END
Other materials:
Fuel Pump Control Module
Component Inspection
CHECK FUEL PUMP CONTROL MODULE (FPCM)
Check the voltage between FPCM terminals under the following conditions.
FPCM Condition
Voltage
(Approx.)
Connector + −
Terminal
B97
6
5
For 1 second after turning ignition switch ON
9.9 V
More than ...
Modes de fonctionnement des essuie-glaces
Type A (selon équipement)
Type B (selon équipement)
Les commandes de visibilité de votre Nissan Rogue s'activent lorsque le contact est sur "ON" :
Mode AUTO / Intermittent :
- Type A (Automatique) : Le Nissan Rogue ajuste seul la vitesse selon l'intensité de la pluie ...
P026b Injection Timing
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P026B
00
Injection timing
Diagnosis condition
—
Signal
—
Threshold
ECM does not control fuel injection timing properly when engine is running ...
