Nissan Rogue (T33) 2021-Present Service Manual: P060b Ecm

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P060b Ecm

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P060B 00

CONTROL MODULE

(Internal control module A/D processing performance) 		Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold ECM internal analog/digital conversion processing system is malfunctioning
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

Is the 1st trip DTC P060B displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P060a Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P060A 00 CONTROL MODULE (Internal control module monitoring proc...
    P060c Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P060C 00 Control module (Internal Control Module Main Processor ...

    Other materials:

    Cvt: Ge0f14a. Symptom Diagnosis
    Cvt Control System Symptom Table The diagnosis item number indicates the order of check. Start checking in the order from 1. Perform diagnoses of symptom table 1 before symptom table 2. Symptom Table 1 Diagnostic item Reference Symptom Shift Shock Slips/Will Not Engage Other ...

    Dtc/circuit Diagnosis. B242a-98 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-98 Closure motor (Closure motor) Diagnosis condition When back door closure function operate Signal (terminal) — Threshold When thermal prot ...

    U2b8c-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U2B8C-88 Ethernet circuit Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold Lost ethernet communication with driving video recorder control module ...