Nissan Rogue (T33) 2021-Present Service Manual: P0522 Engine Oil Pressure

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0522 Engine Oil Pressure

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0522 00

Engine oil pressure sensor/switch

(Engine Oil Pressure Sensor/Switch "A" Low) 		Diagnosis condition Engine speed more than 1000 rpm
Signal (terminal) Engine oil pressure sensor signal
Threshold Sensor signal voltage below minimum threshold.
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Harness or connectors (EOP sensor circuit is open or shorted.)

  • Decrease in engine oil pressure

  • Decrease in engine oil level

  • Cause of engine oil consumption

  • Engine oil condition

  • EOP sensor

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Keep the engine speed at 1,000 rpm for at least 5 seconds.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ENGINE OIL LEVEL

  1. Turn ignition switch OFF.

  2. Check engine oil pressure level. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK ENGINE OIL PRESSURE

With CONSULT

  1. Turn ignition switch ON.

  2. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.

  3. Start the engine and check that “EOP SENSOR” changes, according to engine speeds.

    Monitor item Condition

    Value

    (Approx.)
    EOP SENSOR

    • Engine oil temperature: 80°C (176°F)

    • Selector lever: P or N position

    • Air conditioner switch: OFF

    • No load

    Engine speed:

    Idle     		1.360 V or more

    Engine speed:

    2,000 rpm     		1.670 V or more

Without CONSULT

Check engine oil pressure. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check oil pump. Refer to Removal and Installation.

CHECK EOP SENSOR

Check EOP sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

CHECK ENGINE OIL LEAKAGE

Check engine oil leakage. Refer to Engine Lubrication System.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK CAUSE OF ENGINE OIL CONSUMPTION

Check the following item.

Step Inspection item Equipment Standard Reference
1 PCV valve POSITIVE CRANKCASE VENTILATION : Periodic Maintenance
2 Exhaust front tube Visual

  • No blocking

  • No abnormal sounds

 —
3 Oil pump Visual

  • No blocking

  • No abnormal sounds

 —
Removal and Installation
4

  • Piston

  • Piston pin

  • Piston ring

  • Piston to piston pin oil clearance

  • Piston ring side clearance

  • Piston ring end gap

 Inspection
5 Cylinder block

  • Cylinder block top surface distortion

  • Piston to cylinder bore clearance

 Disassembly & Assembly

>>

Repair or replace error-detected parts.

    P0520 Eop Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0520 00 EOP SENSOR/SWITCH (Engine oil pressure sensor/switch A ...
    P0523 Engine Oil Pressure
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0523 00 Engine oil pressure sensor/switch (Engine Oil Pressure ...

    Other materials:

    Input Speed Sensor
    Exploded View 1. O-ring 2. Input speed sensor 3. Transaxle assembly : N·m (kg-m, in-lb) : Always replace after every disassembly. : Apply petroleum jelly. Removal and Installation REMOVAL Never Reuse These Parts Part Code For additional information: Seal-O-ring 31051 ...

    Adas Control Unit. Basic Inspection
    Additional Service When Replacing Adas Control Unit 2 Without Propilot Assist 2.1 Work Procedure Always perform the additional service after replacing the ADAS control unit 2.ADAS CONTROL UNIT 2 CONFIGURATION Perform saving Nissan Ariya vehicle internal information according to "Replace ECU" i ...

    P2271 Ho2s2
    DTC Description The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the longer switching time. : 0.71 V To judge the malfunctions of heated oxyge ...