Nissan Rogue (T33) 2021-Present Service Manual: P0500 Vss

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0500 Vss

DTC Description

DESCRIPTION

ECM receives vehicle speed signals from two different paths via CAN communication line: One is from the ABS actuator and electric unit (control unit) via the combination unit and the other is from TCM.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0500 00

Nissan Ariya Vehicle SPEED SEN A

(Vehicle speed sensor “A” circuit 		Diagnosis condition

  • Selector lever: D position

  • Nissan Ariya Vehicle speed: 20 km/h (13 MPH)
Signal (terminal) Nissan Ariya Vehicle speed signal
Threshold The difference between a vehicle speed calculated by a output speed sensor transmitted from TCM to ECM via CAN communication and the Nissan Ariya vehicle speed indicated on the combination meter exceeds 15 km/h (10 MPH)
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Combination meter

  • ABS actuator and electric unit (control unit)

  • Wheel sensor

  • TCM

  • Output speed sensor

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Combustion control mode Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0500 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 10 V or more at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine.

  2. Shift the selector lever to D range and wait at least for 2 seconds.

  3. Drive the Nissan Ariya vehicle at least 5 seconds at 20 km/h (13 MPH) or more.

    CAUTION:

    Always drive vehicle at a safe speed.

    NOTE:

    This procedure may be conducted with the drive wheels lifted in the shop or by driving the Nissan Ariya vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0500 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK DTC WITH TCM

Check DTC with TCM. Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Check DTC with ABS actuator and electric unit (control unit). Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK DTC WITH COMBINATION METER

Check DTC with combination meter. Refer to DTC Index (FULL TFT METER) or DTC Index (7 INCH INFORMATION DISPLAY).

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK INPUT SPEED SENSOR

Check input speed sensor. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK WHEEL SENSOR

Check wheel sensor. Refer to below:

  • DTC C106A-04: Refer to DTC Description.

  • DTC C106A-55: Refer to DTC Description.

  • DTC C106A-62: Refer to DTC Description.

  • DTC C106A-64: Refer to DTC Description.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

    P04fa Egr Temperature
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P04FA 00 EGR A control (EGR "A" Control temperature Too High) Di...
    P0506 Isc System
    DTC Description DESCRIPTIONThe ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let into the intake manifold, by operatin...

    Other materials:

    Information Display (combination Meter)
    Door Open Warning DESIGN/PURPOSEInformation display warns the driver that each door is open or is not fully closed. Symbol Message – SYNCHRONIZATION WITH MASTER WARNING LAMPSynchronization is applied.Refer to Master Warning Lamp.SYSTEM DIAGRAMSIGNAL PATH BCM transmits door switch ...

    Dtc/circuit Diagnosis. Parking Brake Switch
    Component Inspection CHECK PARKING BRAKE SWITCH Disconnect the 12V battery negative terminal. Disconnect the parking brake switch harness connector. Check the continuity when parking brake switch is operated. Parking brake switch Continuity Condition Terminals When parking ...

    P0128 Thermostat Function
    DTC Description DTC DETECTION LOGICEngine coolant temperature has not risen enough to open the multi-way control valve even though the engine has run long enough.This is due to a leak in the seal or the multi-way control valve being stuck open. DTC CONSULT screen terms (Trouble diagnosis conte ...