Nissan Rogue (T33) 2021-Present Service Manual: P044d Egr Volume Control Valve Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P044d Egr Volume Control Valve Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P044D 00

EGR SENSOR C

(EGR sensor C circuit high) 		Diagnosis condition Ignition switch ON
Signal (terminal) EGR volume control valve signal
Threshold

ECM detects the following status continuously for 5 seconds or more:

A voltage signal transmitted from the EGR volume control valve position sensor shows too high.
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Harness or connectors

    (EGR volume control valve position sensor circuit is open or shorted.)

  • EGR volume control valve

FAIL-SAFE

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect EGR volume control valve harness connector.

  3. Turn ignition switch ON.

  4. Check voltage between EGR volume control valve harness connector and ground.

    + −

    Voltage

    (Approx.)
    EGR volume control valve
    Connector Terminal
    F81 3 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check harness continuity between EGR volume control valve harness connector and ECM harness connector.

    EGR volume control valve ECM Continuity
    Connector Terminal Connector Terminal
    F81 2 F71 107 Existed

  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check harness continuity between EGR volume control valve harness connector and ECM harness connector.

    EGR volume control valve ECM Continuity
    Connector Terminal Connector Terminal
    F81 1 F71 116 Existed

  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EGR VOLUME CONTROL VALVE

Check the EGR volume control valve. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace EGR volume control valve. Refer to Removal and Installation.

CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between EGR volume control valve harness connector and ECM harness connector.

    EGR volume control valve ECM Continuity
    Connector Terminal Connector Terminal
    F81 3 F71 84 Existed

  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

    P044c Egr Volume Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P044C 00 EGR SENSOR C (EGR sensor C circuit low) Diagnosis condi...
    P044e Egr Volume Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P044E 00 EGR SENSOR C (EGR sensor C circuit high) Diagnosis cond...

    Other materials:

    C106f-54 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106F 54 Steering angle sensor (Steering angle sensor) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. ...

    C1203-86 Abs Signal
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1203-86 ABS SYSTEM (Antilock brake system) Diagnosis condition Ignition switch: ON Nissan Ariya Vehicle running Signal Wheel speed signals ...

    Dtc/circuit Diagnosis. B1002-13 Lap Pre-Tensioner Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1002-13 Lap pre-tensioner RH (Lap pre-tensioner right hand) Diagnosis condition When ignition switch is ON. Signal (terminal) Lap pre-tensioner RH signal ...