Nissan Rogue (T33) 2021-Present Service Manual: P040b Egr Temperature Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P040b Egr Temperature Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P040B 00

EGR TEMP SENSOR A

(EGR temperature sensor A circuit range/performance) 		Diagnosis condition —
Signal (terminal) —
Threshold

ECM detects the following status continuously for 5 seconds or more:

  • A signal transmitted from EGR temperature sensor is 96°C (204°F) or more, even though the signal from ECT sensor is 70°C (158°F) or less.

  • A signal transmitted from EGR temperature sensor is 20°C (68°F) or less, even though warming up of the engine is performed enough and EGR control valve operates.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (EGR temperature sensor circuit is open or shorted.)

  • EGR temperature sensor

FAIL-SAFE

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P040B is displayed with the following DTC, perform the trouble diagnosis for the applicable DTC.

  • P0116

  • P0117

  • P0118

  • P0125

If applicable DTC detected?

YES>>

Perform diagnosis of applicable.

  • DTC P0116: Refer to DTC Description.

  • DTC P0117: Refer to DTC Description.

  • DTC P0118: Refer to DTC Description.

  • DTC P0125: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at ignition switch ON.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE -1

  1. Turn ignition switch ON.

  2. Select “DATA MONITOR” mode with CONSULT.

  3. Check that “COOLANT TEMP/S” indicates lower than 70°C (167°C).

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE -2

  1. Start the engine and warm it up to the normal operating temperature.

  2. Drive the Nissan Ariya vehicle and accelerate it from 50 km/h (31 MPH) to 80 km/h (50 MPH) within 15 seconds.

  3. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P040B is displayed with the following DTC, perform the trouble diagnosis for the applicable DTC.

  • P0116

  • P0117

  • P0118

  • P0125

If applicable DTC detected?

YES>>

Perform diagnosis of applicable.

  • DTC P0116: Refer to DTC Description.

  • DTC P0117: Refer to DTC Description.

  • DTC P0118: Refer to DTC Description.

  • DTC P0125: Refer to DTC Description.

NO>>

GO TO 2.

CHECK EGR TEMPERATURE SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect EGR temperature sensor harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between EGR temperature sensor harness connector terminal and ground.

    + −

    Voltage

    (Approx.)
    EGR temperature sensor
    Connector Terminal
    F28 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 4.

CHECK EGR TEMPERATURE SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between EGR temperature sensor harness connector and ECM harness connector.

    + − Continuity
    EGR temperature sensor ECM
    Connector Terminal Connector Terminal
    F28 2 F71 102 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK EGR TEMPERATURE SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between EGR temperature sensor harness connector and ECM harness connector.

    + − Continuity
    EGR temperature sensor ECM
    Connector Terminal Connector Terminal
    F28 1 F71 104 Existed

  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

CHECK EGR TEMPERATURE SENSOR

Check EGR temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace EGR temperature sensor. Refer to Exploded View.

    P0407 Egr Differential Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0407 00 EGR SENSOR B (EGR sensor B circuit low) Diagnosis condi...
    P040c Egr Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P040C 00 EGR TEMP SENSOR A (EGR temperature sensor A circuit low...

    Other materials:

    P0053 A/f Sensor 1 Heater
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0053 00 HO2S1 HTR B1 (HO2S heater resistance bank 1 sensor 1) Diagnosis condition — Signal (terminal) A/F sensor 1 heater signal Threshold D ...

    Symptom Diagnosis. Engine Can Not Start
    Description Engine does not start when push-button ignition switch is pressed.SYMPTOM TABLE (BOTH INTELLIGENT KEYS HAVE THE SAME SYMPTOMS) Door lock operation (remote keyless entry) Door lock operation (request switch of front/rear/back door) or trunk/back door open operation (opener switch of ...

    Input Speed Sensor
    Exploded View 1. O-ring 2. Input speed sensor 3. Transaxle assembly : N·m (kg-m, in-lb) : Always replace after every disassembly. : Apply petroleum jelly. Removal and Installation REMOVAL Never Reuse These Parts Part Code For additional information: Seal-O-ring 31051 ...