Nissan Rogue (T33) 2021-Present Service Manual: P0130 A/f Sensor 1

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0130 A/f Sensor 1

DTC Description

DTC DETECTION LOGIC

To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1 signal fluctuates according to fuel feedback control.

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0130 00

A/F SENSOR1 (B1)

(O2 sensor circuit bank 1 sensor 1) 		Diagnosis condition Engine run and fuel shut off
Signal (terminal) A/F sensor 1 signal
Threshold The output voltage computed by ECM according to the A/F sensor 1 signal is constant.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A

With CONSULT

  1. Start engine and warm it up to normal operating temperature.

  2. Let it idle for 2 minutes.

  3. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

With CONSULT: GO TO 3.

NO-2>>

Without CONSULT: GO TO 7.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION

  1. Select “A/F SEN1 (B1)” in “DATA MONITOR” mode of “ENGINE” using CONSULT.

  2. Check “A/F SEN1 (B1)” indication.

Does the indication fluctuates around 2.2 V?

YES>>

GO TO 4.

NO>>

Proceed to DTC Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-1

  1. Select “A/F SEN1 (B1) P1276” of “A/F SEN1” in “DTC WORK SUPPORT” mode of “ENGINE” using CONSULT.

  2. Touch “START”.

  3. When the following conditions are met, “TESTING” will be displayed on the CONSULT screen.

    ENG SPEED 1,000 - 3,200 rpm
    VHCL SPEED SE More than 64 km/h (40 mph)
    B/FUEL SCHDL 1.0 - 8.0 msec
    Selector lever D position

    If “TESTING” is not displayed after 20 seconds, retry from step 2.

    CAUTION:

    Always drive Nissan Ariya vehicle at a safe speed.

Is “TESTING” displayed on CONSULT screen?

YES>>

GO TO 5.

NO>>

Check A/F sensor 1 function again. GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-2

Release accelerator pedal fully.

NOTE:

Never apply brake during releasing the accelerator pedal.

Which does “TESTING” change to?

COMPLETED>>

GO TO 6.

OUT OF CONDITION>>

Retry DTC CONFIRMATION PROCEDURE. GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-3

Touch “SELF-DIAG RESULT”

Which is displayed on CONSULT screen?

YES>>

INSPECTION END

NO>>

Proceed to DTC Diagnosis Procedure.

PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B

Perform Component Function Check. Refer to Component Function Check.

NOTE:

Use component function check to check the overall function of the A/F sensor 1 circuit. During this check, a 1st trip DTC might not be confirmed.

Is the inspection result normal?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect A/F sensor 1 harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between A/F sensor 1 harness connector and ground.

    + − Voltage
    A/F sensor 1
    Connector Terminal
    F18 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.

    + − Continuity
    A/F sensor 1 IPDM E/R
    Connector Terminal Connector Terminal
    F18 4 F35 75 Existed

  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.

    + − Continuity
    A/F sensor 1 ECM
    Connector Terminal Connector Terminal
    F18 1 F72 56 Existed
    2 60

  4. Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.

    + − Continuity
    A/F sensor 1
    Connector Terminal
    F18 1 Ground Not existed
    2
    + − Continuity
    ECM
    Connector Terminal
    F72 56 Ground Not existed
    60

  5. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Perform Intermittent Incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

REPLACE AIR FUEL RATIO (A/F) SENSOR 1

Replace air fuel ratio (A/F) sensor 1. Refer to Exploded View.

>>

INSPECTION END

    P0128 Thermostat Function
    DTC Description DTC DETECTION LOGICEngine coolant temperature has not risen enough to open the multi-way control valve even though the engine has run long enough.This is due to ...
    P0131 A/f Sensor 1
    DTC Description DTC DETECTION LOGICTo judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1 signal is not inordinately low. DTC C...

    Other materials:

    B2e32-11 Av Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E32-11 Audio unit (Audio unit) Diagnosis condition When ignition switch is ON Signal (terminal) Sound signal Threshold 0.5 V or less Diagnosi ...

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    Wireless Charger. System Description
    Component Parts Wireless Charger Component Parts Location A. Console finisher assembly No.Component 1. Wireless charger unit 2. Wireless charger indicator Wireless charger unit Wireless charger unit The wireless unit is located at the front of the center console. Wirel ...