Nissan Rogue (T33) 2021-Present Service Manual: P0122 Tp Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0122 Tp Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0122 00

TP SEN 2/CIRC-B1

(Throttle/Pedal position sensor/switch “A” circuit low) 		Diagnosis condition Engine running at idle
Signal (terminal) TP sensor 2 signal
Threshold

  • An excessively low voltage from the TP sensor 2 is sent to ECM

  • An excessively　low throttle open output from the TP sensor 2 is sent to ECM
Diagnosis delay time 1 second

POSSIBLE CAUSE

  • Harness or connectors (TP sensor 2 circuit is open or shorted.)

  • Electric throttle control actuator (TP sensor 2)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0122 is displayed with DTC P06B1, first perform the trouble diagnosis for DTC P06B1.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0122 is displayed with DTC P06B1, first perform the trouble diagnosis for DTC P06B1.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect electric throttle control actuator harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between electric throttle control actuator harness connector and ground.

    + −

    Voltage

    (Approx.)
    Electric throttle control actuator
    Connector Terminal
    F50 3 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    + − Continuity
    Electric throttle control actuator ECM
    Connector Terminal Connector Terminal
    F50 3 F72 62 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK THROTTLE POSITION SENSOR 2 GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    + − Continuity
    Electric throttle control actuator ECM
    Connector Terminal Connector Terminal
    F50 2 F72 45 Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK THROTTLE POSITION SENSOR 2 INPUT SIGNAL CIRCUIT

  1. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    + − Continuity
    Electric throttle control actuator ECM
    Connector Terminal Connector Terminal
    F50 4 F72 52 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK THROTTLE POSITION SENSOR

Check the throttle position sensor. Refer to Component Inspection.

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace electric throttle control actuator. Refer to Removal and Installation.

    P0117 Ect Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0117 00 ECT SEN/CIRC (Engine coolant temperature sensor 1 circu...
    P0125 Ect Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0125 00 ECT SENSOR (Insufficient coolant temperature for closed...

    Other materials:

    Adp Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side). Driver seat control unit Harness con ...

    Basic Inspection. Additional Service When Replacing Air Bag Diagnosis Sensor Unit
    Description After replaced air bag diagnosis sensor unit, it is necessary to perform control unit configuration with CONSULT. For details, refer to Work Procedure. Work Procedure REPLACE AIR BAG DIAGNOSIS SENSOR UNIT Replace air bag diagnosis sensor unit. Refer to Removal and Installation. ...

    Wireless Charger. System Description
    Component Parts Wireless Charger Component Parts Location A. Console finisher assembly No.Component 1. Wireless charger unit 2. Wireless charger indicator Wireless charger unit Wireless charger unit The wireless unit is located at the front of the center console. Wirel ...