Nissan Rogue (T33) 2021-Present Service Manual: P0092 Fuel Rail Pressure Control System

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0092 Fuel Rail Pressure Control System

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0092 00

Fuel pressure regulator 1

(Fuel Pressure Regulator "A" Control Circuit High) 		Diagnosis condition Engine running at idle
Signal High pressure fuel pump signal
Threshold ECM detects High pressure fuel pump circuit is VB short
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Harness or connectors (The high pressure fuel pump circuit is shorted.)

  • High pressure fuel pump

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more.

YES>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

GO to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK HIGH PRESSURE FUEL PUMP CIRCUIT

  1. Turn ignition switch ON.

  2. Disconnect ECM harness connector and high pressure fuel pump harness connector.

  3. Check the continuity between ECM harness connector and high pressure fuel pump harness connector.

    ECM High pressure fuel pump Continuity
    Connector Terminal Connector Terminal
    F72 7 F82 1 Existed
    2 2

  4. Also check harness for short to power and short to ground.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the error-detected parts.

CHECK HIGH PRESSURE FUEL PUMP

Check high pressure fuel pump. Refer to Component Inspection.

Is inspection result normal?

YES>>

INSPECTION END

NO>>

Replace error-detected parts.

    P0091 Fuel Rail Pressure Control System
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0091 00 Fuel pressure regulator 1 (Fuel Pressure Regulator "A" ...
    P0096 Iat Sensor 2
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0096 00 IAT SENSOR 2 B1 [Intake air temperature sensor 2 circui...

    Other materials:

    C1f59-04 Eps Circuit
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F59 04 EPS control unit (Electric power steering control unit) Diagnosis condition When engine is running Signal (termi ...

    P02cd Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CD 00 CYL1 INJECTOR OFFSET LEARNING (Cylinder 1 Fuel Injector "A" Offset Learning At Max Limit) Diagnosis condition Engine running During injector ...

    2wd. Preparation. Preparation
    Preparation Special Service Tool Tool number (TechMate No.) Tool name Description KV40104000 ( – ) Hub lock nut wrench a: 85 mm (3.35 in) b: 65 mm (2.56 in) Removing and Installing wheel hub lock nut. KV40107300 ( – ) Boot band crimping tool Installing bo ...