Nissan Rogue (T33) 2021-Present Service Manual: Mass Air Flow Sensor

Component Inspection

CHECK MASS AIR FLOW (MAF) SENSOR-1

With CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect all harness connectors disconnected.

  3. Start the engine and warm it up to normal operating temperature.

  4. Select “MASS AIR FLOW SENSOR (g/s) B1� in “DATE MONITOR� mode of “ENGINE� using CONSULT and check the indication under the following condition.

    Monitor item Condition Indication
    MASS AIR FLOW SENSOR (g/s) B1 Ignition switch ON (Engine stopped.) 0 g/s
    Idle (Engine is warmed-up to normal operating temperature.) 2.09 - 3.51 g/s
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 3.62 - 6.40 g/s
    Idle to about 4,000 rpm 7.49 - 14.04 g/s

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK FOR THE CAUSE OF UNEVEN AIR FLOW THROUGH INTAKE AIR DUCT

  1. Turn ignition switch OFF.

  2. Check for the cause of uneven air flow through intake air duct. Refer to the following.

    • Crushed air ducts

    • Malfunctioning seal of air cleaner element

    • Uneven dirt like leaves or insects of air cleaner element

    • Intake valve deposit

    • Improper specification of intake air system parts

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK MAF SENSOR-2

With CONSULT

  1. Repair malfunctioning part.

  2. Start the engine and warm it up to normal operating temperature.

  3. Select “MASS AIR FLOW SENSOR (g/s) B1� in “DATE MONITOR� mode of “ENGINE� using CONSULT and check the indication under the following condition.

    Monitor item Condition Indication
    MASS AIR FLOW SENSOR (g/s) B1 Ignition switch ON (Engine stopped.) 0 g/s
    Idle (Engine is warmed-up to normal operating temperature.) 2.09 - 3.51 g/s
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 3.62 - 6.40 g/s
    Idle to about 4,000 rpm 7.49 - 14.04 g/s

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

CHECK MAF SENSOR-3

With CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect all harness connectors disconnected.

  3. Start the engine and warm it up to normal operating temperature.

  4. Select “MASS AIR FLOW SENSOR (g/s) B1� in “DATE MONITOR� mode of “ENGINE� using CONSULT and check the indication under the following condition.

    Monitor item Condition Indication
    MASS AIR FLOW SENSOR (g/s) B1 Ignition switch ON (Engine stopped.) 0 g/s
    Idle (Engine is warmed-up to normal operating temperature.) 2.09 - 3.51 g/s
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 3.62 - 6.40 g/s
    Idle to about 4,000 rpm 7.49 - 14.04 g/s

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace MAF sensor. Refer to Exploded View.

    Manifold Absolute Pressure (map) Sensor
    Component Inspection CHECK MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR Turn ignition switch OFF. Remove manifold absolute pressure (MAP) sensor with its harness connector. Install p...
    Multi-Way Control Valve
    Component Inspection CHECK MULTI-WAY CONTROL VALVE-1 With CONSULT Turn ignition switch ON and engine stopped. On the CONSULT screen, select “ENGINEâ€�>>“WORK SUPPORTâ€...

    Other materials:

    Assistance de limitation de vitesse
    L’assistance de limitation de vitesse est une fonctionnalité avancée intégrée aux systèmes ProPILOT Assist du Nissan Rogue, disponible sur les véhicules équipés d’un Système de localisation sur la carte intégré. Cette fonction est conçue pour aider le conducteur à adapter la vitesse ...

    For Frontal Collision
    When SRS is activated in a collision FOR FRONTAL COLLISION: When SRS is activated in a collisionCAUTION: Due to varying models and option levels, not all parts listed in the chart below apply to all Nissan Ariya vehicles. WORK PROCEDURE Before performing any of the following steps, ensure that ...

    Basic Inspection. Diagnosis and Repair Work Flow
    Work Flow OVERALL SEQUENCEDETAILED FLOWGET INFORMATION FOR SYMPTOM Get the detailed information about symptom from customer. Check the drive mode indicator on the meter appeared. Check the Drive mode indicator on the meter changed when operates the drive mode select switch. &g ...