Nissan Rogue (T33) 2021-Present Service Manual: B12a3-72 Fuel Pump Off Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Power Control System / Ipdm E/r :: Dtc/circuit Diagnosis / B12a3-72 Fuel Pump Off Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC detection condition
B12A3-72

Fuel pump Off circuit

(Fuel pump OFF circuit) 		[ACTUATOR STUCK OPEN] Diagnosis condition When ignition switch is ON
Signal (terminal) CPU monitors the status at the contact and excitation coil circuits of the fuel pump relay inside it
Threshold The fuel pump relay OFF is detected
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Fusible link

  • Fuse

  • Harness or connectors (battery power supply circuit is open or shorted to ground)

  • IPDM E/R

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch OFF.

  2. Ignition switch ON.

  3. Select “Self diagnosis result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FUSE AND FUSIBLE LINK

  1. Ignition switch OFF.

  2. Check that the following IPDM E/R fuse and fusible link is not blown (open):

    Signal name Fuse and Fusible link No. Capacity
    Battery power supply D 100A
    Ignition power supply 85 20A

Is the fuse and fusible link blown (open)?

YES>>

Replace the blown (open) fuse or fusible link after repairing the affected circuit if a fuse or fusible link is blown (open).

NO>>

GO TO 2.

CHECK BATTERY POWER SUPPLY VOLTAGE

  1. Disconnect IPDM E/R connector.

  2. Check voltage between IPDM E/R harness connector and the ground.

    + - Voltage
    IPDM E/R
    Connector Terminal
    E118 2 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

    B120e-55 Ipdm E/r
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B120E-55 IPDM E/R (Intelligent power distribution module eng...
    B20dd-73 Ign Relay on Circ
    DTC Description IPDM E/R operates the ignition relay when it receives an ignition ON signal from BCM via CAN communication. Turn the ignition relay OFF by pressing the push-butt...

    Other materials:

    Removal and Installation. Battery Terminal with Fusible Link
    Exploded View Battery terminal with fusible link : N·m (kg-m, in-lb) : N·m (kg-m, ft-lb) Removal and Installation REMOVALDisconnect the battery cable from the negative terminal. Refer to Exploded View. CAUTION: To prevent damage to the parts, disc ...

    Writing of Calibration Data
    Work Procedure DESCRIPTIONIf only the around view monitor control unit is replaced, the calibration data stored in the camera can be written to the around view monitor control unit by selecting "Camera Calibration" of "Work Support" mode in CONSULT.WORK PROCEDUREWRITE CALIBRATION DATA With C ...

    Symptom Diagnosis. Door Does Not Lock/unlock with Door Request Switch and Intelligent Key
    Description All doors do not lock/unlock using door request switch.SYMPTOM TABLE (BOTH INTELLIGENT KEYS HAVE THE SAME SYMPTOMS) Door lock operation (remote keyless entry) Door lock operation (request switch of front/rear/back door) or trunk/back door open operation (opener switch of trunk/back ...